Lenovo 70LU Скачать руководство пользователя страница 94

Страница: 94 / 142

Figure 77. Installing the front fan assembly

6. Connect the front fan assembly cable to the front system fan connector on the system board. See

“System board components” on page 19.

Rear fan assembly

• “Removing the rear fan assembly” on page 82

• “Installing the rear fan assembly” on page 83

Removing the rear fan assembly

To remove the rear fan assembly, do the following:

1. Prepare your server. See “Preparing your server and removing the server cover” on page 41.

2. Locate the rear fan assembly. See “Server components” on page 16.

3. Disconnect the cable of the rear fan assembly.

4. The rear fan assembly is attached to the chassis by four rubber mounts. Break or cut the rubber mounts

and gently pull the rear fan assembly out of the chassis.

Note:

A new rear fan assembly comes with four new rubber mounts.

ThinkServer TS150 User Guide and Hardware Maintenance Manual

Содержание 70LU















































































































































Результаты поиска

Содержание 70LU

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 70LU, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание 70LU

Отзывы:

Бренды по названию

Популярные бренды