Lenovo 70LU Скачать руководство пользователя страница 90

Страница: 90 / 142

Figure 70. Installing the thermal sensor

4. Connect the thermal sensor cable to the thermal sensor connector on the system board. See “System

board components” on page 19.

SD module

• “Removing the SD module” on page 78

• “Installing the SD module” on page 79

Removing the SD module

To remove the SD module, do the following:

1. Prepare your server. See “Preparing your server and removing the server cover” on page 41.

2. Lay the server on its side for easier operation.

3. Locate the SD module. See “Server components” on page 16.

4. Disconnect the SD module cable.

5. Remove the SD module from the SD module bracket.

Figure 71. Removing the SD module

6. Both sides of the SD module support the installation of an SD card. If any SD card is installed, remove

the card.

ThinkServer TS150 User Guide and Hardware Maintenance Manual

Содержание 70LU















































































































































Результаты поиска

Содержание 70LU

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 70LU, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание 70LU

Отзывы:

Бренды по названию

Популярные бренды