Lenovo 6241 Скачать руководство пользователя

Страница: 367 / 1990

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

•

405-907-000 : BRCM:TestLEDs Test Failed

A failure was detected while verifying operation of the status LEDs.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

DSA Brocade test results

The following messages are generated when you run the Brocade test.

Test results for the DSA Brocade test

The following messages can result when you run the DSA Brocade test.

•

218-000-000 : Brocade:MemoryTest Passed

The test passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Appendix B. DSA diagnostic test results

353

Содержание 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 6241

Отзывы:

Похожие инструкции для 6241

Бренды по названию

Популярные бренды

Lenovo 6241, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 6241

Отзывы:

Похожие инструкции для 6241

Бренды по названию

Популярные бренды