manualshive.com logo in svg

Lenovo 30CY, Руководство по техническому обслуживанию аппаратной части, Страница: 73 / 224

Поделиться
Скачать
Lenovo 30CY Скачать руководство пользователя страница 73

Chapter 6. Advanced configuration

This chapter provides information to help you further configure the computer.

Using the Setup Utility program

The Setup Utility program is used to view and change the configuration settings of your computer. This 
section provides information about only the major configuration settings available in the program.

Note:

The operating system settings might override any similar settings in the Setup Utility program.

Starting the Setup Utility program

To start the Setup Utility program, do the following: 

1.  Turn on or restart your computer.

2.  Before the operating system starts up, repeatedly press and release F1 or Fn+F1 (depending on the 

keyboard settings). Based on the Setup Utility display mode setting, one of the following situations 
occurs: 

•  Text mode: The Setup Utility program opens.

•  Graphic mode (available on some models): The start screen is displayed. Then, select 

Setup 

and 

press Enter to open the Setup Utility program.

Note:

If a BIOS password has been set, the Setup Utility program will not open until you enter the 

correct password. For more information, see “Using BIOS passwords” on page 68.

To view and change the configuration settings, follow the instructions on the screen. 

Changing the display language of the Setup Utility program

The Setup Utility program supports three display languages: English, French, and simplified Chinese.

To change the display language of the Setup Utility program, do the following: 

1.  Start the Setup Utility program. See “Starting the Setup Utility program” on page 65.

2.  From the main interface, locate 

System Language 

and press Enter.

3.  Select the display language according to your needs.

Enabling or disabling a device

This section provides information about how to enable or disable user access to hardware devices (such as 
USB connectors or storage drives).

To enable or disable a device, do the following: 

1.  Start the Setup Utility program. See “Starting the Setup Utility program” on page 65.

2.  Select 

Devices

.

3.  Select the device you want to enable or disable and press Enter.

4.  Select the desired setting and press Enter.

5.  To save settings and exit the Setup Utility program, press F10 or Fn+F10 (depending on the keyboard 

settings). Then, select 

Yes 

in the window displayed, and press Enter.

© Copyright Lenovo 2018, 2020

65

Содержание 30CY

































































































































































































































Отзывы:

Нет отзывов