Lennox V0STAT54P-2 Скачать руководство пользователя страница 21

Страница: 21 / 22

Error Codes

• The V0STAT54P-2 controller displays

the last 10 error codes. To view error
codes, see the instructions on the pre-
vious page.

• If the error code is for an indoor unit,

the unit address also displays.

Figure 19. Error Code Display

MODE

FAN SPEED

Error Code

Indoor Unit Address

Table 4. Indoor Unit Error Codes

Error
Code

Description

Communication error
between the indoor unit and
the wired controller (may
aﬀ ect other indoor units in the
system)

Communication error be-
tween the indoor unit and the
controller

Controller EEPROM error

Communication error be-
tween the indoor unit and the
outdoor unit

T1 temperature sensor error

T2A temperature sensor error

T2B temperature sensor error

Outdoor unit error

Fan motor error

Indoor unit EEPROM error

Indoor unit DC motor error

Condensate pump error

Содержание V0STAT54P-2























Результаты поиска

Содержание V0STAT54P-2

Отзывы:

Бренды по названию

Популярные бренды

Lennox V0STAT54P-2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание V0STAT54P-2

Отзывы:

Бренды по названию

Популярные бренды