Lennox LS25 Series Скачать руководство пользователя страница 1

Страница: 1 / 24

Page 1

INSTALLATION

INSTRUCTIONS

SEPARATED COMBUSTION UNIT HEATERS

508064-01

1/2021

Replaces 10/2020

Shipping and Packing List ..............................................2

125/200 Unit Dimensions Single Fan .............................3

250/400 Unit Dimensions Dual Fan ................................4

Unit Parts Arrangement ..................................................5

Optional Accessory .........................................................6

Requirements in USA .....................................................6

Requirements in Canada ................................................6

Additional Requirements ................................................7

Unit Heater Installation ...................................................7

Combustion and Ventilation Air.....................................10

Venting..........................................................................10

Electrical Connections ..................................................15

Gas Connection ...........................................................19

Leak Check ..................................................................20

Unit Start-Up ................................................................20

To Turn Off Gas to Unit

................................................21

Heating Sequence of Operations ................................21

Ignition Control LED ....................................................22

High Altitude Adjustments ............................................22

Gas Flow .....................................................................22

Gas Pressure Adjustments ..........................................22

Limit Control Switch ......................................................23

Louver Vane Adjustment ..............................................23

Combustion Air Pressure Switch .................................23

Flame Roll-out Switch ..................................................23

Service..........................................................................23

Start-Up and Performance Checklist ...........................24

LS25

125,000 to 400,000 Btuh Series

Table Of Contents

WARNING

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, personal injury

or loss of life. Installation and service must be performed

by a licensed professional installer (or equivalent), service

agency or the gas supplier.

CAUTION

As with any mechanical equipment, personal injury can

result from contact with sharp sheet metal edges. Be

careful when you handle this equipment.

Note - Unit heaters are designed for indoor use only.

RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

WHAT TO DO IF YOU SMELL GAS:

Do not store or use gasoline or other

cinity of this or any other appliance.

formed by a qualified installer, service

agency or the gas supplier.

Do not try to light any appliance.

Leave the building immediately.

Do not touch any electrical switch; do not use

any phone in your building.

Immediately call your gas supplier from a

neighbor's

structions.

If you cannot reach your gas supplier, call the

fire department.

FIRE OR EXPLOSION HAZARD.

Failure to

ly could result in serious injury, death,

or property damage.

WARNING

Be sure to read and understand the

structions in this manual.

ation, service or maintenance can cause

serious injury, death or property damage.

Содержание LS25 Series

























Результаты поиска

Содержание LS25 Series

Отзывы:

Похожие инструкции для LS25 Series

Бренды по названию

Популярные бренды

Lennox LS25 Series, Руководство по установке

Результаты поиска

Содержание LS25 Series

Отзывы:

Похожие инструкции для LS25 Series

Бренды по названию

Популярные бренды