manualshive.com logo in svg

Lennox KDB024, Руководство по установке

Поделиться
Скачать
Lennox KDB024 Скачать руководство пользователя страница 34

Page 34

WARNING

This product contains a chemical known to the
State of California to cause cancer, birth defects, or
other reproductive harm.

G-Burners

Periodically examine burner flames for proper
appearance during the heating season. Before each
heating season examine the burners for any deposits or
blockage which may have occurred.

Clean burners as follows:

1- Turn off both electrical power and gas supply to unit.

2- Remove blower access panel.

3- Remove top burner box panel and screws securing

burners to burner support and lift the individual
burners or the entire burner assembly from the
orifices. See figure 26. Clean as necessary.

4- Locate the ignitor under the right burners. Check

ignitor spark gap with appropriately sized twist drills
or feeler gauges. See figure 27.

5- Replace burners and screws securing burner. See

figure 26.

6- Replace access panel.

BURNER BOX ASSEMBLY

FIGURE 26

GAS VALVE

GAS MANIFOLD

FLAME

SENSOR

BURNER

ASSEMBLY

IGNITOR

FIGURE 27

IGNITOR

SPARK GAP

SHOULD BE 1/8”

(3mm)

 

WARNING

Danger of explosion. Can cause injury or
death. Do not overtighten main burner
mounting screws. Snug tighten only.

7- Restore electrical power and gas supply. Follow

lighting instructions attached to unit and use
inspection port in access panel to check flame.

H-Combustion Air Inducer

A combustion air proving switch checks combustion air
inducer operation before allowing power to the gas
controller. Gas controller will not operate if inducer is
obstructed.

Under normal operating conditions, the combustion air
inducer wheel should be checked and cleaned prior to the
heating season. However, it should be examined
periodically during the heating season to establish an
ideal cleaning schedule. With power supply
disconnected, the condition of the inducer wheel can be
determined by looking through the vent opening.

Clean combustion air inducer as follows:

1- Shut off power supply and gas to unit.

2- Disconnect pressure switch air tubing from

combustion air inducer port.

3- Remove the mullion on the right side of the heat

section.

4- Remove and retain screws securing combustion

air inducer to flue box. Remove vent connector.
See figure 28.

5- Clean inducer wheel blades with a small brush and

wipe off any dust from housing. Clean accumulated
dust from front of flue box cover.

6- Replace the mullion on the right side of the heat

section.

Содержание KDB024




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды