manualshive.com logo in svg

Lennartsfors IronHorse 2013, Руководство оператора

Поделиться
Скачать
Lennartsfors IronHorse 2013 Скачать руководство пользователя страница 18

Edition 2015-03-31 

18 

 

 

 

Fuel

 

 

Fuel safety 

 

 

 

 

 

 

 

 

 

 
 
The following are absolutely forbidden when 
fuelling: 

 

• To smoke.

 

 

• To have flames or hot objects in close 

proximity. 

 

• To have the engine running

. 

 

Petrol 

 

Use leaded or unleaded petrol. 
The lowest recommended octane grade is 90. If 
you run the engine on a lower octane grade than  
90 so-called knocking can occur. This leads to an 
increased engine temperature, which can result in 
serious engine damage. 

 

Refuelling 

1. Clean around the fuel cap. 

 

2. Open the fuel cap slowly so that any 
 excess pressure is released. 

 

3. Tighten the fuel cap carefully after fuelling. 
Clean the fuel tank regularly.  

 

The fuel filter should be changed at least once a 
year. Contamination in the tanks causes 
malfunction. 

 

 

 

 

 

 

FIG 31 

 

WARNING! 

The fuel used in the IronHorse has 
the following hazardous 
properties: 
1.  The fluid, its vapour, and its        

exhaust fumes are poisonous. 

2.  Can cause skin irritation. 

3.  Is highly inflammable 
 

Содержание IronHorse 2013






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды