Lemair LWTT80, Руководство пользователя

Страница: 8 / 9

-9- -8-
After you use the washing machine, never forget to do the following two things:
Attention To Maintenance
Cabinet maintenance
Cleaning the lint filter
After using the washing machine,wipe
the moisture and stain on it with a piece
of soft cloth.To avoid damage to the
surface,do not use corrosive or volatile
chemicals.
Anti-freezing protection
▲
To prevent from freezing:
▲
If the water is frozen, please take the following steps:
Cabinet
Frame
◆
◆
◆
◆
Press the button head, and
pull the lint filter out.
Turn the filter net inside out, and rinse it
in water.
After inserting the claw, press the button
to insert it into place.
A sound of “ba” means proper installation.
Button head
Claw
hose completely.
Lay the drain hose and turn the drain selector knob to the "Drain”position to
empty the water in the tub.
①
water inlet
②
Turn off the water tap, remove the water inlet hose and empty water in the
Keep about 2 liters of warm water below 50
℃
in the wash tub for
about 10 minutes. and then lay the drain hose and turn the
wash drain selector knob to the "Drain”position to empty the water .
Fit the water inlet hose and turn on the water tap to
confirm water filling and draining work properly.
①
②
③
Put the water inlet hose into warm water of about 50
℃
.
Operation when objects are
dropped into the outside of the spin tub
①
Remove all screws on the frame with a screw driver and
loosen the connector of the brake belt .
②
Pull up the frame with both hands and turn it backwards.
③
Take out the clothes dropped into the outside of the spin tub.
④
Fasten the connector of the brake belt ,Press the frame to
reset and tighten screws.
2. Remove the water inlet hose.
1. Disconnect the power plug.
-8-
Maintenance
Notes
The washing machine employs alternative current with rated voltage and frequency . When voltage fluctuates
between -10% and 10% of the rated voltage, the machine can work normally.
Connection mode of the power cord of this machine is Y-shaped connection.Users
reconnect the wire by themselves.
please contact the designated service center.
should not detach or
If this part needs to be repaired,
Usage method
B.Buzzer function
(For machines having buzzer function only)
●
Fold in half along
the long edge
●
1/3 fold in the
same direction
Roll up the blanket
●
Put into the tub with
blanket edge facing down
●
Dilute detergent with water (below 50
℃
), then pour the solution into
Fold the blanket as shown in the figure, and into the wash tub.
①
adequate the wash tub.
②
put it
This machine can wash blended blanket (less than 3 kg) marked with the "hand washing"
label.Washing method is as follows:
Wash timer
Soak
35
15
10
5
Work time
about 5 about 5 about 5 Total: 35 (mins)
about 1.5
about 1.5
about 2
Static time
For seriously stained clothes, Soak wash is useful to achieve better wash result.
15-35 minutes of the wash timer is for soak wash:(illustrate as follows)
35 15
(unit
：
)
mins
Special Features
A.Soak function
(For machines having soak function only )
Function of the buzzer is to alarm finish of washing,and it is helpful to control wash process
.
●
Buzzer will alarm the completion of washing.
The dual voltage washing machine can work at the voltage of 220V or 127V to meet needs of different
countries and areas.
Unplug the washing machine plug to cut off the power supply.
Remove the back cover.
Take down the nylon clip, and remove the plastic bag.
Connect the Wash127V of the terminal connector with “Wash”, “Spin127V” with “Spin” , then the voltage
can be converted to “127V60Hz”.
Put the wires in order, wrap them in the plastic bag, and refix the back cover. Then the washing machine
can be powered for operation.
If convert the voltage from 127V60Hz to 220V60Hz:
Steps - are the same as above
Connect the “Wash 220V” of the terminal connector with “Wash”, “Spin 220V” with “Spin” to convert the
voltage to .
The step is the same as above
In the step above, should connect the terminal connectors of both wash and spin, and make sure to
connect correctly.
*The factory-set voltage is 220V60Hz . Users can chose the voltage according to the regional voltage range.
●
convert the voltage from 220V60Hz to 127V60Hz :
①
②
③
④
“ ”
⑤
●
①②③ ① ③
④
220V60Hz
⑤ ⑤
④
“ ”
C.The dual voltage
(For machines having the dual voltage function only)
(For efficiency program only )
Efficiency Program
The tests were carrid out under program Normal . Below is the detail for test seting and steps;
1. Main wash: 30 min., H water level, wash temperature 40
℃;
2
.
Spin: 3 min., 2 times; 4 kg test load for one turn;
3. Rinse: 3 min., L water level, water temperature 20
℃;
4. Spin: 3 min., 2 times; 4 kg test load for one turn.