●
Be sure to use plug that is properly grounded.
The maximum gradient of the supporting surface for the washing machine should not exceed 2
º
.
Do not tear down electrical wires and components in the machine by yourself.
There are holes on the base for ventilation. These holes should not be blocked by foreign objects
(carpets, etc.).
Never connect the grounding wire with the live wire, or it may lead to an electric shock.
If the power cord is damaged, it must be replaced by a qualified person to avoid a hazard.
●
Do not connect to the hot water supply.
●
●
●
●
●
●
After using, be sure to unplug the power plug.
If the following symptoms occur, please disconnect the power plug and perform the
following checks:
After you use the washing machine, never forget to do the following two things:
Attention To Maintenance
Cabinet maintenance
Cleaning the lint filter
After using the washing machine,wipe
the moisture and stain on it with a piece
of soft cloth.To avoid damage to the
surface,do not use corrosive or volatile
chemicals.
Anti-freezing protection
▲
To prevent from freezing:
▲
If the water is frozen, please take the following steps:
Cabinet
Frame
◆
◆
◆
◆
Press the button head, and
pull the lint filter out.
Turn the filter net inside out, and rinse it
in water.
After inserting the claw, press the button
to insert it into place.
A sound of “ba” means proper installation.
Button head
Claw
hose completely.
Lay the drain hose and turn the drain selector knob to the "Drain”position to
empty the water in the tub.
①
water inlet
②
Turn off the water tap, remove the water inlet hose and empty water in the
Keep about 2 liters of warm water below 50
℃
in the wash tub for
about 10 minutes. and then lay the drain hose and turn the
wash drain selector knob to the "Drain”position to empty the water .
Fit the water inlet hose and turn on the water tap to
confirm water filling and draining work properly.
①
②
③
Put the water inlet hose into warm water of about 50
℃
.
Operation when objects are
dropped into the outside of the spin tub
①
Remove all screws on the frame with a screw driver and
loosen the connector of the brake belt .
②
Pull up the frame with both hands and turn it backwards.
③
Take out the clothes dropped into the outside of the spin tub.
④
Fasten the connector of the brake belt ,Press the frame to
reset and tighten screws.
2. Remove the water inlet hose.
1. Disconnect the power plug.
Check that the power supply is in good condition.
Check that the power plug is inserted properly.
●
●
●
Check that the wash timer knob or the spin timer knob is not
in the "0" position.
Check that the drain hose is not laid too high.
Check that the drain hose is not frozen.
Check that the drain hose is not blocked by foreign matter.
●
●
●
Check that there are no coins or any other foreign objects
dropped into the wash tub.
●
Check that the washing machine is placed on flat, stable floor.
Check that clothes are evenly distributed in the spin tub.
Check that there are no washing materials or foaming debris
dropped into the outside of the spin tub.
●
●
●
The washing
machine does
not work.
The drain hose
does not work.
There is abnormal
noise during washing.
There is abnormal
noise and violent
vibration during
spinning.
Symptom
Reason
-9-
-8-
Maintenance
Maintenance
-8-
Notes
The washing machine employs alternative current with rated voltage and frequency . When voltage fluctuates
between -10% and 10% of the rated voltage, the machine can work normally.
Connection mode of the power cord of this machine is Y-shaped connection.Users
reconnect the wire by themselves.
please contact the designated service center.
should not detach or
If this part needs to be repaired,
Main Technical Parameters
Capacity (dry Clothes)
Power Supply
Input Power (lower drain)
Input Power (upper drain)
Maximum Time
Water volume
Maximum
water
pressure
Overall dimension
Net weight
Pump Input Power
Wash
8.0 kg
400W
400W
15 min. 35 min.(soak
wash)
HI:77L H: 72L M: 61L L: 50L
Spin
4.6kg
135W
135W
5 min.
/
0.6Mpa
870x512x957(mm)
23kg
23.5kg
30W
240V/50Hz
Lower Drain System
Upper Drain System
