SAUSAGE MAKING
ASSEMBLY INSTRUCTIONS
5
LEM Products • West Chester, OH 45011 • PH: 877-536-7763 • lemproducts.com
Handle
Cylinder
Upper Cylinder Brackets
Main Shaft
Lower Cylinder Brackets
FFigure 1
Slow Drive Shaft
Fast Drive Shaft
Piston
Retaining Ring
1. Place the Stu er onto a stable table or workspace.
2. Attach the Handle to one of the Drive Shafts and turn to
raise the Piston out of the Cylinder and into the
Piston’s highest position.
3. Place the Cylinder into the Lower Cylinder Brackets and
pivot the Cylinder back into the frame of the machine.
Push the Cylinder back into the Upper Cylinder Brackets to
lock into place.
4. Remove the Retaining Ring from the Cylinder by turning it
counter-clockwise.
5. Insert the S
Tube of your choice through the
Retaining Ring.
6. Turn the Retaining Ring and S
Tube assembly
clockwise onto the Cylinder, until the assembly is hand
tight. DO NOT OVERTIGHTEN.
Socket Cover
Mounting Thumbscrew
Socket
Mounting Hole
Slow Drive Shaft
Fast Drive Shaft
Stu er Motor
Motor Housing
Plug
Thumbscrew
1. W
at dull object, such as a screwdriver,
remove the Socket Cover.
2. Insert the plug of the sensor into the socket
on the side of the sausage stu er gear box. Slide the
Stu er Motor onto the Slow Drive
Shaft lining up the Mounting Thumbscrews to the
Thumbscrew Mounting Holes.
Caution:
The plug of the sensor must be plugged
into the socket entirely. If plug is not securely
inserted the Piston will not be able to stop at the
cylinder bottom or the highest position automati-
cally. This may cause the motor to overload or
possibly damage the stu er or motor. This type of
damage
IS NOT
covered under warranty.
3. Screw the Mounting Thumbscrews into the holes on
the side of the stu er. Be sure to snugly tighten
these three Mounting Thumbscrews to secure the
Stu er Motor onto the stu er.
1. With the sensor cord securely attached to the stu er and plug in the power cord.
2. Press the power button to turn the motor on. The light will illuminate.
3. Press the “UP” button to raise the piston. Unit will automatically stop at the upmost position.
Note:
"Up" has only one speed. "Down" speed adjustable by turning the knob.
4. Remove the Cylinder from the base by tilting it forwar
top brackets. Lift the C
ower brackets.
5. Fill the Cylinder and reinstall Cylinder on mounting brackets.
6. To slowly lower the Piston turn the speed adjustment knob all the way left and press the "down" button on the motor
or depress the Foot Pedal. When the Piston reaches the meat mixture, and all of the air pockets are removed and meat
is extruded t
e, hit "Stop" or release foot pedal, once the "STOP" button is pressed or the foot
pedal released the piston will automatically raise for a couple seconds. This function will help to st
ow of meat
thr
e. This will occur every time the stop is pressed or foot pedal is released.
7. Place casing ov
twist, tie or clip end.
8. Press “DOWN” butt
g. Use the speed dial to control the speed of the piston.
9. The Piston will continue to move down the stu er until it reaches the bottom of the Cylinder. At that time it will stop
for a few seconds and then automatically rise to the highest position and then stop.
NOTE:
Do not operate the stu er for longer than one hour at a time or unit may overheat.
Turn Power Switch t
ow unit to cool for 15 minutes.
NOTE:
When making snack sticks or using the smallest tube it is highly recommended t
s. or less at a time.
Adding additional water to your mix will also help with this process. Additional meat in the cylinder or a ver
will make the motor work extra hard and may cause the circuit breaker to pop. If this happens refer to circuit breaker
information below.
MOTOR ASSEMBLY INSTRUCTIONS
8
LEM Products • West Chester, OH 45011 • PH: 877-536-7763 • lemproducts.com
CRICUT BREAKER
The stu er motor is equipped with a circuit breaker. If the motor stops working completely it may be
due to the circuit breaker tripping.
To reset circuit breaker
• The power ligh
tch will be out.
• Press the power switch to the OFF position.
• Press the circuit breaker reset button on the underside of the stu er motor.
• Press the power switch to the on position, the light will illuminate.
• You can now resume use.
NOTE:
Do not operate the stu er for longer than one hour at a time or unit may overheat. Turn Power Switch
t
ow unit to cool for 15 minutes.
WARNING
Severe injury risk!
At all times k
top of the cylinder.
