LELY Lely Discovery 90 SW Скачать руководство пользователя страница 17

Страница: 17 / 150

5.4006.8501.0

Safety

2-1

Safety

2.1

Introduction

The Discovery 90 SW is an automated machine. Therefore it is of the utmost importance to obey all safety
instructions.

2.2

Signal Icons

Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The signal
word for each message uses the following guidelines:

Danger
Indicates a hazardous situation which, if not avoided, will result in
death or serious injury.

Warning
Indicates a hazardous situation which, if not avoided, could result in death or serious
injury.

Caution
Indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.

Notice
Is used to address practices not related to physical injury e.g. property damage.

Tip
Indicates information that may help the reader, but not hazard related.

in n o vato rs in ag ric u ltu re

Содержание Lely Discovery 90 SW























































































































































Результаты поиска

Содержание Lely Discovery 90 SW

Отзывы:

LELY Lely Discovery 90 SW, Руководство оператора, Страница: 17 / 150

Результаты поиска

Содержание Lely Discovery 90 SW

Отзывы: