LELY Attis PT 130 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 92

background image

3.

OPERATION

3.1

Hydraulic control panel

Read the tractor manual for the correct procedures to operate the tractor
hydraulics.

The operator switches the handle(s) or moves the joystick to operate the
Attis. The following positions of the switches or joystick enable an action to
the hydraulic system:

•

Floating (~)

The floating position opens the supply and return valves. The oil pressure
is not available in the system, but passive hydraulic movements are
possible. This position is used when working and disconnecting the
machine.

•

Neutral (N)

The neutral position closes the supply and return valves. The oil pressure
is available in the system, but no hydraulic movements are possible.

•

Forwards/Reverse

The forward/reverse operations activate the hydraulic system. The
hydraulic operation of the Attis depends on how the hydraulic hoses are
connected to the tractor:

• Oil flows to cylinders,
• Oil flow returns to tank.

1.Neutral (N) - 2. Forwards - 3. Reverse - 4. Floating

Figure 11. Panel hydraulic operation positions

Note:

Operation

3-1

W-H003.1403EN

«
...
27
28
29
30
31
...
»

Содержание Attis PT 130





























































































Отзывы:

Нет отзывов

Похожие инструкции для Attis PT 130

Бренд: Tascam Страницы: 80

Бренд: Tascam Страницы: 2

Бренд: Walker Страницы: 24

Бренд: PANDROL Страницы: 36

Бренд: Badger Basket Страницы: 7

Бренд: Backyard Discovery Страницы: 53

Бренд: Jackco Страницы: 6

The Wave Transformer

Бренд: EarthQuaker Devices Страницы: 21

Бренд: Wahl Страницы: 2

Бренд: Labelmate Страницы: 61

Бренд: Labconco Страницы: 62

Бренд: Hach Страницы: 456

Бренд: DAAB Страницы: 12

Бренд: StarDental Страницы: 2

Бренд: USC Страницы: 29

Бренд: Parkside Страницы: 88

DSO8000E Series

Бренд: Hantek Страницы: 95

Бренд: Marcy Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды