Leitronic AG EasyAlarm BASIC Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 32

Leitronic AG EasyAlarm BASIC Скачать руководство пользователя страница 8

8

4.2 Operation with potential free alarm contacts (EasyAlarm BASIC)

4.2.1 Safety notes



Function switch must be shifted to OFF and telephone-cord must be disconnected before any wiring work is
done on the AC-adapter or connecting cable.



All contacts of the EXT port are on telephone circuit potential => therefore any applied alarm contact must be
potential free (relays or opto-coupler) and must have a isolation of lease 3.75kV according to regulation
EN60950.



All contacts have to be protected against any body contact

4.2.2 Installation

1.

Slide

function switch

to OFF

2.

Insert 9V battery



into compartment on rear side of alarm unit



Please note: The telephone cord must be disconnected before opening the battery compartment because otherwise
you can get in contact with the telecommunication voltage!

Operation with alarm contacts



Details according to section 5

3.

Plug sensor-cord



in one o the EXT/

≂

-port of alarm unit and connect potential free alarm sensor as following

FCC8/6

Plug

Open ends of sensor-cord

PIN 2:

White wire (Output)

PIN 3:

Black wire (Sensor-2 input)

CAN BE USED AS EMEGENCY MODE!

PIN 4:

Red wire (+12V)

PIN 5:

Green wire (Sensor-1 input)

PLUG&PROTECT-sensor

PIN 6:

Yellow wire (GND)

PIN 7:

Blue wire (Sensor-3 input)

CANNOT BE DISARMED!

4.2.2.1

Operation with only one alarm contact (Sensor-1)

If you need only one alarm contact you should use sensor-1-input.

EasyAlarm

®

will auto-detect the contact-type (



Plug&Protect-Contact)

and starts monitoring sensor-1 according to the state of the sensor-2-input at the time of power-up

(details according to section 4.1.4):

Sensor-1 is a normally closed contact => Connect Sensor-2-input to GND
Sensor-1 is a normally open contact => Leave Sensor-2-input open

4.2.2.2

Operation with up to three alarm contacts (NO or NC)

Select the appropriate contact to fit the monitoring!
Notes:



Sensor-1 monitoring can be disarmed (disable) or sensor-1 can be used for presence verification (



programming

according to section 5.1)



Sensor-2 monitoring can be disarmed (disable) or sensor-2 can be used as a emergency contact (



programming

according to section 5.2)



Sensor-3 monitoring CANNOT be disarmed (



programming according to section 5.3)

Connect power supply

4.

Connect the AC-adapter cable



into the other EXT/

≂

-port of the alarm unit

Telephone connection

5.

Plug enclosed telephone-cord



into



-Line-Jack of alarm unit and connect it with the telephone network



If you share line with modem/telephone please proceed according to section 10.6

S ensor 1

S ensor 2

S ensor 3

Type of contact: Norm ally open (NO)

N orm ally closed (NC)

Potential free !

(t

o

A

C

-a

d

p

te

r)

2

1

4

3

«
...
6
7
8
9
10
...
»

Содержание EasyAlarm BASIC

































Отзывы:

Нет отзывов