Leigh R9 PLUS Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 18

Leigh R9 PLUS Скачать руководство пользователя страница 2

22

ROUTER TABLE OPERATION

R9

PLUS

Joinery System User Guide

Introduction

2000

2090

Your New Leigh R9

PLUS

Joinery System

for Dovetails and Box Joints

Note: There are two user guides in this book.

This user guide is for

Router Table Operation. Flip the book over for Bench Operation.

The R9

PLUS

Joinery System was designed to overcome the

restrictions of fixed width jigs. Because of its unique “step over”
feature, it is possible to rout Through Dovetails and Box Joints
on boards of

ANY

width!

The R9

PLUS

can be used as a template jig with a hand-held router

or as a router table template. In either mode, you will be able
to rout multiple sizes of perfectly fitting through dovetails and
box joints.

Customer Support

If you have any questions that are not answered in this user guide,
please call Leigh Customer Support:

1-800-663-8932

in North

America or email:

[email protected]

For support contacts in

your country of purchase see the Customer Support section of
the Appendix.

Reminder: If at first you don’t succeed, read the instructions!

Important! Inches and Millimeters

Text  and  illustrations  in  this  English  language  user  guide
indicate  dimensions  in  both  inches  and  millimeters,  with
“inches” first, followed by “millimeters” in square brackets, i.e.

1

⁄

2

"x 2"[12x50mm].

Do not be concerned that the inch/millimeter equivalents are
not mathematically “correct.” Just use the dimensions that
apply to your guides and bits.

Patents Pending

What’s in the Box:

PART NO. QUANTITY PART DESCRIPTION

2000

1

R9

PLUS

Template

2090

1

User Guide

BAG 1

2030

2

Latches

2040

1

Glide

2080

1

Side Stop

BAG 2

2010

3

Pin Plates

BAG 3

2050

2

Beam Assembly Screws, ¼"-20 x 2¾"

2055

2

Beam Assembly Wing Nuts, ¼"-20

2060

2

Latch Screws, Phillips 10-24 x ¾"

2065

2

Latch Nuts, Nyloc

2070

11

Wood Screws, Phillips Flat Head, No.8 x 1¼"

2075

1

Side stop Screw, Phillips Round Head, No.8 x ¼"

BAG 4

e10

1

e10 e-Bush (Guide Bushing)

80-8

1

Dovetail Bit, ½"-8º

160

1

Straight Bit, ½" Two Flute

172-8

1

Collet Reducer, ½" to 8mm

730V

1

Pin Wrench

BAG 5

2020

2

Clamp Locators

9505

2

F-Clamps

«
1
2
3
4
...
»

Содержание R9 PLUS



















Отзывы:

Нет отзывов