Leguan 135 NEO Скачать руководство пользователя

Страница: 54 / 66

TROUBLESHOOTING

The following table shows failures and malfunctions of the access platform and the ways to repair
them.

ISSUE

CAUSE

CORRECTIVE ACTION

the motor does not start when
the START button is pushed
(also see the engine

manufacturer’s manual).

The main power switch is in the

‘OFF’ position.

The emergency stop switch is
turned down.

The motor is too cold.

The fuel faucet is closed.

The fuel tank is empty.

Empty start battery.

The combustion engine fuse
(inside the ignition) has blown.

Turn the switch on.

Release the emergency stop
switch by turning it.

Use the choke.

Open the fuel faucet (petrol
engine).

Refill.

Charge the battery by
connecting the 230 V plug.

Replace the fuse (also see the
engine manual).

The motor does not start when
the START button is pushed (see
also the engine manual).

Connection flaw in the wiring.

Faulty START switch.

Use a meter to check voltages,
wires and connections.

Replace the switch.

The electric motor does not
start when the start lever is
pulled.

Mains cable is not connected to
network.

The emergency stop switch is
turned down.

The main power switch is in the

‘OFF’ position.

Empty battery.

Connect the plug to the
230V/16A output.

Release the emergency stop by
turning it.

Turn the switch on.

Charge the battery by
connecting the 230 V plug.

Содержание 135 NEO



































































Результаты поиска

Содержание 135 NEO

Отзывы:

Похожие инструкции для 135 NEO

Бренды по названию

Популярные бренды

Leguan 135 NEO, Руководство оператора и по обслуживанию

Результаты поиска

Содержание 135 NEO

Отзывы:

Похожие инструкции для 135 NEO

Бренды по названию

Популярные бренды