background image

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following 
measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Caution

: Any changes or modifi cations to this device not explicitly approved by 

The Watt Stopper could void your authority to operate this equipment.

Warranty Information

Manufacturer warranties its products to be free of defects in materials and 
workmanship for a period of fi ve (5) years. There are no obligations or liabilities 
on the part of manufacturer for consequential damages arising out of, or 
in connection with, the use or performance of this product or other indirect 
damages with respect to loss of property, revenue or profi t, or cost of removal, 
installation or reinstallation.

2800 De La Cruz Blvd. 

Santa Clara, CA 95050

Phone: 800.879.8585

www.wattstopper.com

Please 

Recycle

1061 South 800 East

Orem, UT 84057

Phone: 800.555.9891

www.vantagecontrols.com

03884r2 9/2007

Watt Stopper Customers contact: 

Vantage Customers contact:

Содержание Wattstopper Vantage Miro MRP6









Отзывы: