background image

Ins

tallation Ins

tructions

Please read all instructions before installing

DESCRIPTION AND OPERATION

The RT-50 is a time switch that turns OFF the connected light or fan when the 
selected time expires. The light behind the ON/OFF button illuminates while the 
switch is OFF. One of the time button indicators is always lit to indicate the last 
used timer.

Manual ON

Turn ON the connected light or fan by pressing the desired time button, or the 
ON/OFF button. If you press the ON/OFF button, it activates the timer that was 
last used.

Manual OFF

While a timer is active, you can press the ON/OFF button to turn OFF the 
connected light or fan without delay. 

Changing the selected time

If you decide that you need more or less time than you originally selected, restart 
the time switch by pressing the button that matches the amount of time you think 
you’ll need.

RT- 50

Time Switch

7- Button Preset

   

6 time selection buttons with 
activation indicator lights

Lighted Switch
ON/OFF Button

SPECIFICATIONS

Voltage ....................................................................... 120VAC, 60HZ
Load (Single Pole Circuit)
 

Incandescent or fl uorescent lamp  ........................... 0 – 600 Watt

 Fan 

Motor 

............................................................................1/6HP

Time Delay...............................................1, 5, 10, 20, 30, 60 minutes
Environment .......................................... Residential Indoor use only
Operating Temperature ..............................32° to 131°F (0° to 55°C)
Humidity ....................................................95% RH, non-condensing
Tools Needed
 Insulated 

Screwdriver

 Wire 

Strippers

Santa Clara, CA 95050

Call 888.817.0571 for Technical Support

Содержание WattStopper RT-50







Отзывы: