manualshive.com logo in svg

LEGRAND Wattstopper LMCT-100-2, Руководство пользователя, Страница: 20 / 30

Поделиться
Скачать
LEGRAND Wattstopper LMCT-100-2 Скачать руководство пользователя страница 20

20

The Load Shed utility determines how the loads in the room will 

respond to a Load Shed command via BACnet.

L o a d   S h e d   M e n u

SHEDS ALL ROOM LOADS!

S h e d   t o   L e v e l :  

< 6 5 >

T i m e o u t   M i n u t e s :  

< 3 0 >

M o d e :  

< N o   O v e r r i d e >

    SEND                  DONE

Shed to Level

The maximum level the load will go to when it receives a Load 

Shed command. If the load is currently at a higher level, it will 

reduce to this amount. If it is currently at a lower level, it will 

remain at that level. Once the load shed is relinquished, the load 

will go to the level determined by the next highest priority. This 

could be the setting of a switch such as a scene switch, or the 

level set as part of a schedule.
Available values: 5% to 100%, in 5 % increments, and Load. If 

set to Load, the load will use the individual Shed to Level that 

can be set for a specific load. LMCS-100 software is required to 

access that parameter.

Timeout Minutes

This limits the amount of time after the Load Shed occurs 

before relinquishing the load shed. Available values are 5 to 250 

minutes in 5 minute increments, and Off. If set to Off, the load 

shed is not relinquished until a command is received via BACnet 

to do so.

Mode

This parameter has three possible values:

• 

No Override

 – Initiates the load shed, but does not allow 

users to adjust the lighting levels

• 

Override

 – Initiates the load shed, but allows users to 

adjust the lighting levels

• 

Disable

 – Prevents the load from responding to the load 

shed command.

Once you have edited the parameters as needed, choose 

SEND

 

and press Select, then point at an IR receiver and press Select 

again. To exit , press 

DONE

.

Status

U t i l i t i e s   M e n u

S m a r t W i r e

I d e n t i f y   D e v i c e s

F o r c e   S y s t e m   i n t o   P n G

R o o m   M o d e

L o a d   S h e d

S t a t u s

  

   

D o n e

A panel or bridge is required to use this option. It provides 

status information on loads, groups, photosensors, and sensors 

connected to the panel or bridge.
An additional screen containing status information specific to 

panels is also available from the 

Panel Setup

 screen. See 

“Panel Status” on page 24

.

Load Status

S t a t u s   –   P a n e l

L o a d   S t a t u s

G r o u p   S t a t u s

L i g h t   L e v e l

O c c u p a n c y   S e n s o r s

  

   

D o n e

This set of screens displays details about each load in the panel, 

as well as any loads in connected room controllers.

Smart Wire

U t i l i t i e s   M e n u

S m a r t W i r e

I d e n t i f y   D e v i c e s

F o r c e   S y s t e m   i n t o   P n G

R o o m   M o d e

L o a d   S h e d

S t a t u s

  

   

D o n e

S m a r t W i r e   M e n u

S t a r t   S m a r t W i r e

S t o p   S m a r t W i r e

  

   

D o n e

The Smartwire feature is used to configure LMSW buttons and 

DLM occupancy sensors to control relays in the LILM series 

Lighting Integrator panel. 
With 

Start Smartwire

 selected, point the LMCT-100-2 at the 

switch or sensor to be programmed and press Select to enter 

the Smartwire mode. Select Stop Smartwire and point at the 

device to exit the Smartwire mode. 

NOTE: 

The LILM panels are no longer sold, so this option is for 

legacy support only.

Identify Devices

U t i l i t i e s   M e n u

S m a r t W i r e

I d e n t i f y   D e v i c e s

F o r c e   S y s t e m   i n t o   P n G

R o o m   M o d e

L o a d   S h e d

S t a t u s

  

   

D o n e

       Identify Device 01-06

LMRC-102     0461385398
HW: 10 Year         14 Week

HW Version:                008

FW Version:          005.025

    

NEXT

    PRIOR    DONE  

Identify Devices provides access to service information for 

individual DLM devices in the room. Note that this feature only 

works with DLM room devices shipped after January 2012.
The room controller (or panel) assigns a number to each device 

when connection between devices is first established. The 

NEXT

 and 

PRIOR

 buttons will cycle through the devices in that 

order. The number in the upper right corner shows the device 

number and total number of devices. In the example above the 

room controller is device 1 of 6 in the local network. The room 

controller (or panel) will always be the first device.

Force System into PnG

U t i l i t i e s   M e n u

S m a r t W i r e

I d e n t i f y   D e v i c e s

F o r c e   S y s t e m   i n t o   P n G

R o o m   M o d e

L o a d   S h e d

S t a t u s

  

   

D o n e

F o r c e   S y s t e m   i n t o   P n G

I f   y o u   a r e   s u r e   y o u

w a n t   t o   f o r c e   a   P n G

P o i n t   t o   A N Y   I R

e n a b l e d   d e v i c e ,   a n d

P r e s s   ‘ S e l e c t ’

Forcing a PnG will reset the room devices back to their original 

Plug and Go states and the room will immediately initiate a fresh 

Plug and Go sequence.

Room Mode

U t i l i t i e s   M e n u

S m a r t W i r e

I d e n t i f y   D e v i c e s

F o r c e   S y s t e m   i n t o   P n G

R o o m   M o d e

L o a d   S h e d

S t a t u s

  

   

D o n e

S e t   R o o m   M o d e

S e l e c t   e i t h e r   N o r m a l

H o u r s   o r   A f t e r   H o u r s

N o r m a l   H r s

        A f t e r   H r s

Room Mode will force the mode of the room into the After Hours 

or Normal Hours mode. Since sensor settings changed while in 

After Hours mode will apply only when the room is in that state, 

switching to After Hours mode will allow testing of the settings 

when a room is usually in Normal Hours. Be sure to return the 

room to the proper mode before exiting.

Load Shed

U t i l i t i e s   M e n u

S m a r t W i r e

I d e n t i f y   D e v i c e s

F o r c e   S y s t e m   i n t o   P n G

R o o m   M o d e

L o a d   S h e d

S t a t u s

  

   

D o n e

Содержание Wattstopper LMCT-100-2































Отзывы:

Нет отзывов