background image

Wattstopper

 

®

Wireless Network Manager
Gestionnaire de Réseau Sans Fil
Administrador de Red Inalambrico

Quick Start Guide • Guide de démarrage • Guía de inicio rápido

No: 24200 – 07/16  rev. 1

Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo: 225CWS

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

INITIAL SETUP

1.  Connect the back up battery to the printed circuit board. To do this, begin by pressing 

down simultaneously on the release tabs (see Figure 3) on each side of the modem 

to remove the plastic casing. Proceed by inserting the white JST connector at the end 

of the red and black wiring into the JST socket. Refer to Figure 4 for location of socket 

and Figure 5 for orientation.

CAUTION

  Danger of explosion if battery is incorrectly replaced. Replace only with 

the same or equivalent type. Batteries should be recycled or disposed of 

as per state and local guidelines.

NOTE: 

Please allow the 225CWS to charge the battery for 120 minutes before 

performing upgrades. 

2.  Connect the power supply to the 225CWS. If required, connect optional 3G antenna 

to the SMA connector, and the JenNet antenna to the RP-SMA connector.

IMPORTANT 

The 225CWS has a back-up battery in case of power interruptions  to ensure the device shuts down properly. Allow the 

225CWS to charge the battery for 120 minutes before removing power from the unit. If shutdown is required prior to this time, 

use the manual shutdown function in the Host App. Please note the status of your unit, indicated by the amber LED heartbeat 

indicator. InferStack starts automatically and indicates a ready state when the LED blinks once or twice per second. If the 

status light does not enter this pattern, do not remove power as that could cause the device to corrupt. Please call Tech 

support if the light does not enter that pattern after an extended period of time.

3.  Once InferStack has started, the device will broadcast a WiFi network with an SSID 

the same as the first 2 sections of your Host ID. The Host ID can be located on the 

label of the device, or on the box the device came in.

  Example: 225CWS-C1234567890-ABCD1234
The default passphrase for this is the last 8 characters of your Host ID, and is case 

sensitive. Connect to this network with your computer.
  Example: 225CWS-C1234567890-ABCD1234

4.  Using the Web browser of the computer connected the to the WiFi network, navigate 

to http://192.168.10.1. The InferStack login screen will appear. 

5.  The default username: su

Default Password: The last 8 characters of your host ID.
The ID is located on the label of the device or the label on the box.
  Example: 225CWS-C1234567890-ABCD1234

6.  Once you log in to the device, you will load the InferStack interface on the DB Builder app. See Figure 6 on page 2. 

Figure/Figura 1

5.3” / 135 cm

1.7” / 42 cm

1.3” / 33 cm

JENNET

USB

LAN

RS-232 POWER SUPPLY

ALIMENTATION

FUENTE DE ALIMENTACIÓN

(15 V DC 1 amp)

3G

Figure/Figura 2

Figure/Figura 3

Figure/Figura 4

Figure/Figura 5

Push Tabs To Open

USB

Heart Beat

SYS

Reset

ETH

RS-232

15VDC

Battery

JST Socket

T O P    V I E W

JST Socke

t

Power Cord

S I D E    V I E W

Slide into place

Insert pins here

JST Socket

Power Cord

cut out

Pins

 

back wall

back wall

Flip so cut out 

is resting 

against the 

back wall of the 

JST Socket.

Отзывы: