LEGRAND On Q lyriQ Скачать руководство пользователя страница 5

 

 
301 Fulling Mill Road, Suite G 
Middletown, PA 17057 
Phone (800) 321-2343 / Fax (717) 702-2546 
www.onqlegrand.com

 

 

 

 

 

 

 

 

 

 

 

 

 

                  

 

 

Page 5 of 8

 

INSTRUCTION/INSTALLATION SHEET 
lyriQ™ Studio High Performance 
Keypad

IS-0425 REV. A

 

  ©Copyright 2009 by On-Q/Legrand All Rights Reserved. 

4.   Operation  
 

A. ON/OFF: 
 

Keypad – Press STANDBY button to toggle ON or OFF (see 

Figure 5

). 

 

Remote – After pressing On-Q button, press On/Off button to 
toggle ON or OFF (see 

Figure 6

). 

 
B. Power-Save 

Mode: 

 

Keypad only – After 30 seconds of inactivity, the Keypad will go 
into Power-Save or “sleep” mode. Pressing any button on the 
Keypad will awaken it from this mode, performing the action 
associated with the button push.  

 
C. SOURCE select: 
 

Keypad – Press SOURCE rocker switch up (right side) or down 
(left side) to select desired source (see 

Figure 5

). 

 

Remote – Press SOURCE UP or DOWN button to select desired 
source (see 

Figure 6

). 

 

NOTE: (Keypad or Remote) For Single Source Systems, source 
toggles between source #1 and any connected Studio Local 
Source/s. For Multi-Source Systems, source toggles between 1, 
2, 3, 4 and connected Studio Local Sources. If more than one 
Local Source is connected, they are indicated by “L” and “2”. 
NOTE: Upon source change, volume mutes and then ramps 
back up to prior volume setting automatically. 

 

D.  VOLUME Steps: Keypad or Remote – Press (Up) or VOLUME –

(Down) button (36 steps). 

 
E.  MUTE: Keypad or Remote – Press MUTE button to toggle Mute On or Off. 

 

NOTE: When returning from MUTE, volume control will ramp to pre-
mute or adjusted state (source, volume and backlight level).  

 

F.  DO NOT DISTURB (see 

Figure 5

): 

When the Keypad is off, pressing MUTE toggles Do Not Disturb (DND). 
This mode is indicated by both the red POWER and MUTE LED on. 
When Keypad is in DND mode, it will Not respond to whole house 
commands from other locations. 

 
G.  WHOLE-HOUSE Mode (see 

Figure 5

): 

 

NOTE: In this mode, every operation performed on this keypad will be 
relayed to all keypads not in (DND) mode in the system. 
 

Keypad or Remote – Press the WHOLE HOUSE button to toggle the 
Whole House function On or Off (On the Keypad, the WHOLE HOUSE 

Figure 5 

Source 
 LEDs 

Source 

Button 

Mute 
Button 

Volume 
Buttons/ 
LEDs 

IR 

Target 

Standby 

Button 

Whole 
House 
Button 

Figure 6 

On-Q 

Button 

Source 
Buttons 

Volume 
Buttons 

Mute 

Button 

Whole 
House 
Button 

Room 
Button 

Local 

Button 

i Button 

On/Off 
Button 

On-Q Universal 
Remote  
(P/N AU1060) 

Содержание On Q lyriQ









Отзывы: