Leggett & Platt Falcon 2.0+ Скачать руководство пользователя страница 13

Страница: 13 / 24

Falcon™ 2.0+ Owners Manual 290-0009-b

FALCON

™

2.0+ REMOTE CONTROL PROGRAMMING

Program Two Remotes to Operate One Base

- Bases

are factory programmed to operate individual
bases. To program two remotes to operate one
base, perform the following numbered procedure.

If programming fails, initiate the programming

procedure a second time.

Program Two Remotes to Operate Two Bases

Bases are factory programmed to operate individual
bases. To program two remotes to operate two
bases, perform the following numbered procedure.

If programming fails, initiate the programming

procedure a second time.

REMOTE

CONTROL 1

REMOTE

CONTROL 2

REMOTE

CONTROL 1

REMOTE

CONTROL 2

BASE 1

BASE 2

STEP 1

UNPLUG

the base from the electrical power source

(if plugged in) and wait 3 minutes.

STEP 2
Plug the base into the electrical power source.

You now have 3 minutes to complete the
programming procedure. The programming indicator
(under bed light) will flash to indicate programming
mode.

STEP 3
Simultaneously press and hold the

head up

and

foot up

buttons on

remote control 1

for 2 seconds.

Release both buttons and set remote control 1 aside
without pressing any other button.

NOTE: If

any

button is pressed, remote control will

exit pairing mode.

STEP 4
Simultaneously press and hold the

head up

and

foot up

buttons on

remote control 2

for 2 seconds.

Release both buttons.

Press the

head up

foot up

button on

remote

control 2

to verify base functions.

Wait 5 seconds and press the

head up

foot up

button on

remote control 1

to verify base functions.

NOTE: There should be a 5 second wait time while

switching between remote control 1 and remote

control 2.

Two remote controls are now programmed to operate
one base.

STEP 1

UNPLUG

both bases from the electrical power

source (if plugged in) and wait 3 minutes.

STEP 2
Plug

both

bases

into the electrical power source.

You now have 3 minutes to complete the
programming procedure. The programming indicator
(under bed light) will flash to indicate programming
mode.

STEP 3
Simultaneously press and hold the

head up

and

foot up

buttons on

remote control 1

for 2 seconds.

Release both buttons and set remote control 1 aside
without pressing any other button.

NOTE: If

any

button is pressed, remote control will

exit pairing mode.

STEP 4
Simultaneously press and hold the

head up

and

foot up

buttons on

remote control 2

for 2 seconds.

Release both buttons.

Press the

head up

foot up

button on

remote

control 2

to verify base functions.

Wait 5 seconds and press the

head up

foot up

button on

remote control 1

to verify base functions.

NOTE: There should be a 5 second wait time while

switching between remote control 1 and remote

control 2.

Two remote controls are now programmed to operate
two bases.

Содержание Falcon 2.0+

























Результаты поиска

Содержание Falcon 2.0+

Отзывы:

Похожие инструкции для Falcon 2.0+

Бренды по названию

Популярные бренды

Leggett & Platt Falcon 2.0+, Руководство пользователя

Результаты поиска

Содержание Falcon 2.0+

Отзывы:

Похожие инструкции для Falcon 2.0+

Бренды по названию

Популярные бренды