Assembly of becco® coupling
Scope of delivery (Illus. 7) ____________________________________
I
Rubber band (if required)
II
Outer coupling plate with pre-fitted traction component
III
Inner coupling plate
IV
2 x M6 hexagonal socket screws with spring washer
V
M6 safety nut with washer
VI
M5 safety nut with washer
Mounting the coupling (Illus. 10)_______________________________
The rubber bands provided must be mounted in the case of drum
brakes, hub circuit and frame protection to ensure uniform frame thick -
ness.
a) Adapt the rubber strips to suit the frame diameter.
b) Fit the rubber band in front of and behind the fixing clip.
Mount the coupling in accordance with the illustration.
Note: tighten the two upper screws (V), followed by the two lower nuts
(VI, VII).
Important: the outer coupling plate prism should touch the bicycle
frame tube exactly (Illus. 8).
Warning: Tighten the screws evenly and not too extremelytoo tightly.
The coupling plates must lie parallel to each other and should not be
warped (Illus. 9).
Note: Use of the stand coupling or hub coupling is recommended with
thick bicycle frames, disk brakes and rear spring suspension (mountain
and city bikes). These are available as accessories.
Hitching and unhitching (Illus. 11-19)
Hitching __________________________________________________
Open the coupling lever. Press the shorter lever upwards with your thumb
and flip completely forwards.
Push the coupling laterally over the traction component on the coupling
plate.
Close the coupling. Flip the longer lever to the rear and then press down-
wards until the coupling engages.
Warning: The coupling lever should be engaged completely.
Check security by pulling sideways.
Loop the retention device straps around the bicycle frame and close with
the buckle.
Warning: It is imperative that the safety catch be fitted for safety rea-
sons.
Unhitching ________________________________________________
Release the retention device.
Open the coupling.
Pull the coupling housing away to the side.
Close the coupling again.
Note: The trailer should only be stored with the coupling closed to avoid
damage.
1
2
11
12
13
14
15
16
17
18
19
Содержание Cuatro
