Operation
• DANGER! Never operate product in an explosive atmosphere. Electric power tools and battery powered tools can
create sparks, which may ignite flammable liquids, dusts, or fumes.
• DANGER! Because of the high working pressures developed by this gun, the possibility of grease injection into the
flesh, or an eye, is a potential hazard. Never allow any part of the human body to come in front of, or in direct
contact with a grease discharge outlet or potential hose rupture. Never point the nozzle of the gun at yourself or
toward anyone else. If accidental grease injection should occur, seek Immediate Emergency Medical Attention.
DO NOT try to treat the injury yourself! If injection occurs, provide grease product information to medical
personnel. Be certain that any and all system components will withstand the pressures being developed. Never
exceed the pressure rating of any component in the system. Inspect all hoses and fittings before each use.
Weak, worn, or damaged hoses are a hazard. Do not use any defective, unmarked, or damaged hoses.
Do not repair
the grease whip hose. Replace if damaged.
• WARNING: Grease gun can develop high pressure – up to 6000 psi (408 bar). Use safety glasses and gloves for
protection during operation. Keep hands clear of the exposed rubber or plastic portion of hose. Extreme pressure
may cause nozzle extension or grease hose to burst.
• CAUTION: Inspect and tighten all fluid connections regularly and replace weak or damaged hoses or other
components with suitable replacements that will withstand the pressures developed.
• CAUTION: Release trigger if blocked line causes grease gun to stall.
Continued operation could damage the motor.
CHARGER OPERATION:
The battery pack is not fully charged out of the carton.
Read and understand all of the safety instructions,
and then follow the battery charging instructions that follow.
•
Make sure power cord circuit voltage is the same as that shown on the charger. Connect charger to the power source.
•
Place battery pack in charger cavity. Do not force. The slot in the charger must align with the raised boss on the battery pack.
When proper contacts are made, the green light will appear.
•
Press the SET button; the green light will go out and the red light will glow, indicating the charger has switched
to quick-charge mode.
• Charge the battery for one full hour including quick-charge time prior to initial use.
•
When the battery pack is fully charged, the red light will go out and the green light will glow.
The battery pack will continue to receive a trickle charge. Remove the battery pack from the charger.
•
Disconnect charger power cord from the power source when not charging battery pack.
• Important: Battery pack temperature will increase during and shortly after use.
The battery pack may not accept a full
charge if charged immediately after use. For best results, allow the battery pack to cool to room temperature before charging.
GREASE GUN OPERATION:
• Insert fully-charged battery pack into the end of the grease gun handle by aligning the slot in the handle with the
matching boss on the battery pack.
Do not force objects. Make certain battery pack is fully engaged into handle cavity and
snaps into place on both sides at battery pack latch buttons. Depress tool switch momentarily to check battery pack
connection to tool. To release battery from tool handle, depress both battery pack latch buttons simultaneously until battery
will release and can be withdrawn straight out from cavity in tool handle. Do not allow metal objects to contact battery
pack terminals while battery is not in charger or tool.
• Re-Priming:
Follow procedure for cartridge loading (see “Assembly” section), but do not reload. This procedure will allow
the gun to reprime using the automatic bleeder valve. If necessary, repeat the process until all trapped air pockets
have been purged from the grease barrel.
• Connect grease coupler to standard grease zerk fitting on equipment or machinery to be greased.
Release trigger to
stop grease flow. To disconnect grease coupler from zerk, angle the coupler and use a twisting motion. If the coupler will
not disengage, the tip sleeve of the coupler can be loosened with tools to allow adjustment in the tension of
the coupler gripping the grease zerk fitting. Retighten the coupler sleeve to prevent coupler leaking.
• Operate the switch to dispense grease.
The switch must be continuously depressed to dispense grease. If back pressure
in the grease line exceeds the 6000 psi limit, grease will then be expelled from the pressure relief valve to limit the pressure in
order to reduce risk of motor overload and limit excessive grease pressure in grease hose. Do not exceed
specifications or alter gun to perform beyond ratings. Such misuse will void warranty and can result in possible injury.
