LH01791:05/00
LH01791:05/00
LH01791:05/00
LH01791:05/00
LH01791:05/00
4
PREPARATION FOR INSTALLATION OF DROPSIDE:
Loosen the four Slotted/Phillips Screws
A
(Dropside
only) which attach the Stabilizing Bar
V
to the Headboard
A A
and Footboard
Z
to prepare for Dropside
X
X
X
X
X
installation. Back out these
(4)
Screws a full
(8)
revolu-
tions each, but do not remove the screws
.
The Stablizing
Bar
V
will now be loose.
Install Dropside
X
by following substeps
I
through
IV
listed below. Refer to
Diagram
.
(It would be helpful to
have a friend assist you with this procedure.)
Note: the
outside location of Dropside
X
X
X
X
X
as shown in Dia-
gram.
I.
Note:
During the Dropside
X
installation procedure
use extreme caution when Top Tracks and Lower Tracks
make contact with Upper Guide Bushings
C
C
C
C
C
and Lower
Guide Pins
D
D
D
D
D
so as not to damage the finish of this crib.
II.
Insert the Upper Guide Bushings
C
C
C
C
C
(mounted to
Footboard
Z
and Headboard
AA
in
STEP 3
)
into the
Upper Tracks
(metal)
which were factory mounted to
Dropside
.
Hold the Dropside
X
at approximately 30
degrees from vertical as shown in
Diagram
.
III.
Once both ends are engaged, then carefully allow
Dropside
X
to slide downward. Then rotate the bottom
end of the Dropside
X
until it is nearly vertical.
(
Note:
Rotation will be stopped when the dropside
X
touches
the Lower Guide pins
D
D
D
D
D
.
Carefully let the Dropside
X
slide down until it is as low as it can go.
IV.
READ THIS STEP COMPLETELY BEFORE PROCEEDING.
Next, lift
Dropside
X
X
X
X
X
approximately two inches (2") vertically. This will put Dropside
X
in the proper vertical alignment with the Lower Guide Pin
D
D
D
D
D
which will
be inserted into the Lower Tracks
(Right & Left)
.
Flex the bottom end of the corner post on the Dropside
side of Footboard
Z
away from the Dropside
X
. The purpose of this process is to create a gap
for the Lower Guide Pins
D
to pass through so that the Lower Guide Pins
can be inserted into the long groove of the plastic Lower Tracks. As you
prepare to accomplish this please note the following:
If the Stabilizing Bar Assembly
V
was not loosened enough
(as described
in PREPARATION FOR INSTALLATION OF DROPSIDE in the beginning
of this
Step
)
there will not be enough slack to create the necessary gap
required for the Lower Guide Pin
D
to pass through. Prematurely forcing the
pin through a gap with inadequate clearance could damage the finish on the
Dropside
X
. If your crib has too small of a gap, then lower Dropside
X
to its
lowest position and check to verify that preparation at beginning of
Step 5
was performed correctly.
If it was performed correctly, but the gap is still too small, it may be because
the Stabilizing Bar
V
assembly needs to be pulled away from the bottom rails
of the Footboard
Z
or Headboard
AA
. Check to verify that the End Plates
M
&
N
have been pulled away from the bottom rails until they touch the
underside of the heads of loosened Slotted/Phillips Machine Screws
A
A
A
A
A
.
After the Lower Guide Pin
D
D
D
D
D
has been installed into the long groove on
Footboard
Z
, then repeat this process on Headboard
AA
. After both Lower
Guide Pins
D
are installed, very carefully and slowly raise the Dropside
X
up until it locks into its raised position. Be very careful to watch to ensure that
the Lower Guide Pins
D
located in the grooves do not slip out during the
process of raising Dropside
X
.
Refer to
Diagram 3.
Tighten the
(4)
Slotted/Phillips Machine Screws
A
A
A
A
A
which
were installed in
Step 3
to attach Stabilizing Bar
V
to Headboard
AA
and
Footboard
Z
but were loosened in
Step 5
. Be sure the
(4)
Slotted/Phillips
Machine Screws
A
A
A
A
A
are tightened securely. Check these screws periodically
and tighten if needed.
Check the function of Dropside
X
. To lower the Dropside, lift
up on the Dropside top rail with your hand near the middle and
then press in with your knee on the center of the Dropside
bottom rail. The Dropside will then lower. To lock the Dropside
in the raised position, just lift it up until it locks into place.
Always verify that both ends of the Dropside are locked in the
raised position whenever child is placed in crib. Only lower
the Dropside when attending to child. Lower crib Dropside
X
X
X
X
X
prior to proceeding with Step 6.
S
TEP
5 - D
IAGRAM
5:
I
NSTALLATION
OF
D
ROPSIDE
.
Corner post of Footboard
ZZZZZ
X
30°
II
II
II
II
II
.
Engagement
of Metal Top
Track and
Upper Guide
Bushing
C
C
C
C
C
will
start at bottom
of Metal Top
Track
(see
enlarged
section view
below).
long groove
short groove
Outside of Dropside
X
X
X
X
X
Y
Z
D
H
U
III
.
Lower Track
( Plastic)
NOTE:
Place short groove
toward inside of crib.
II
.
ENLARGED SECTION VIEW
Engagement of Metal Top
Track
and Upper
Guide Bushing
C
C
C
C
C
X
Z
C
Z
X
IV
IV
IV
IV
IV
.
ENLARGED VIEW
IV
.
Then insert Lower Guide Pin
D
D
D
D
D
into
long groove in Lower Track
(plastic).
FLEX
Corner post to receive Dropside
XXXXX
Metal Top
Track
