![background image](http://html1.mh-extra.com/html/legacy/lcd87dfx/lcd87dfx_owners-manual_1868534006.webp)
ELECTRIC CONNECTION
BASIC OPERATION
5
6
(for RDS model only)
TA function [TRAFFIC ANNOUNCEMENT] BUTTON(For RDS only)
Press it to scan up by one channel step with station detection. If a valid signal has detected,
the current frequency is blinked with in 5 seconds, then press it again to stop scan and
remain the current frequency; otherwise, the unit continue to scan up by one channel step
with station detection 5 seconds later.
Press it to switch between 4 preset equalizer curves:FLAT,CLAS,POP M,ROCK M,The
sound quality will be changed.
Press it to eliminate the sound immediately.
If the front panel is not on the main unit, LED will be flashing.
.
RESET button is placed on the housing and must be activated with either a
ballpoint pen or thin metal object. The RESET button is to be activated for the
following reasons:
-Initial installation of the unit when all wiring is completed.
-All the function buttons do not operate.
-Error symbol on the display.
Note: If press RESET button, the unit can
work yet, please use a cotton swab
soaked in isopropyl alcohol to clean the socket on the back of the front panel.
When PTY is selected, the radio starts to search corresponding PTY information, and stops if the
corresponding PTY information is detected.
If corresponding PTY information is not existed any more, PTY type is automatically exit to
normal mode.
20.TA BUTTON
21.SCAN BUTTON
22.DSP BUTTON
23.MUTE BUTTON
24.FLASHING LED
25 RESET
When pressed short, it is activated as TA mode on or off.
When TA mode is on and traffic announcement is transmitted:
1).When the unit is in CD mode, it will switch to radio mode temporarily.
2).Temporary switch over to an EON linked station when EON detects a traffic
announcement on that other program.
3).If the volume level was under the threshold point, it will be raised to the threshold point.
But the user changed the volume level which was more than the threshold point(min. TA
volume level),it will be set to the last level.
't
When pressed long , it is selected
mode.
The purpose of this key is to reduce unwanted EON TA switching, which EON TA
information was received from current station and the radio switched to that EON
linked station, but no information could not be received because the EON linked
station is located too far from that area.
So the radio is switched back to current station again.
In above operation, a customer listen to a wrong program or mute sound for a while.
-
mode
When the filed strength level of EON linked is less than the threshold level, the radio
does not switch that station, and a customer can hardly listen to any disturbances.
When EONTA LOACL mode is selected, EONTA LO on numeric display is indicated
for a few seconds.
-
mode
EON TA switching is try to implemented by the information of current station .
When EONTA DISTANCE mode is selected, EONTA DX on numeric display is
indicated for a few seconds.
EONTA LOCAL / EONTA DISTANCE
EONTA LOCAL
EONTA DISTANCE
NOTE:
In spite of having any kinds of speaker system, must use 4 ohms
impedance of speaker to reduce the distortion during high volume
level.
FOR WOOFER( 4X40W)
FOR 4X40W
FUSE
BOX
FRONT RCA OUTPUT
CABLE(optional)
RCH RED
LCH WHITE
RCH RED
LCH WHITE
cable(optional)
AUX
YELLOW
RED
IGNITION
SWITCH(B+)
MEMORY(B+)
GROUND(B-) BLACK
BLUE
AUTO
ANTENNA
WHITE
WHITE/BLACK
GREY
/BLACK
GREY
GREEN
/BLACK
GREEN
VIOLET
/BLACK
VIOLET
FRONT
Lch SPK
REAR
Lch SPK
FRONT
REAR
Rch SPK
Rch SPK
ANTENNA CONNECTOR
0.5A
OR
CDCcannector(optional)
GREEN
FUSE
BOX
FRONT RCA OUTPUT
CABLE(optional)
RCH RED
LCH WHITE
YELLOW
RED
IGNITION
SWITCH(B+)
MEMORY(B+)
GROUND(B-) BLACK
BLUE
AUTO
ANTENNA
WHITE
WHITE/BLACK
GREY
/BLACK
GREY
GREEN
/BLACK
GREEN
VIOLET
/BLACK
VIOLET
FRONT
Lch SPK
REAR
Lch SPK
FRONT
REAR
Rch SPK
Rch SPK
ANTENNA CONNECTOR
0.5A
SUB WOOFER
RCA
RCH RED
LCH WHITE
cable(optional)
AUX
OR
CDCcannector(optional)