Legacy Stoves SF170 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 51

background image

NOTE: This unit is not approved for use in
mobile homes.

Clearances Required for Safety and

Operation

It is important to provide su:cient clearance

around the boiler for convenient servicing and
cleanout.

e required minimums as measured from

the boiler vessel are shown below:

SF170/SF270 Clearances

Front:

48 Inches

Right:

24 Inches

Rear:

36 Inches

Left:

24 Inches

Top:

24 Inches

Boiler Clearances Illustrated

Refer to Appendix B: Speci9cations for exterior

dimensions of the various models. For commercial
and residential installations, many boiler codes
require a minimum of 3 feet of clearance on all sides.
You must follow your local code requirements when

these are more strict than the guidelines in this
manual.

DOMESTIC HOT WATER

FROM YOUR BOILER:

DOMESTIC COIL OPTION

is option is used in the Legacy Stoves coal

boiler to supply hot water for domestic home use.
With this option in place, your boiler can provide
large amounts of hot water heated by low cost solid
fuel.

ese coils operate on the principle of heating

water as it passes through 9ne copper tubing
immersed in the boiler water, instead of a separate
tank.

A tempering valve should be installed in the hot

water supply line to reduce the temperature of the
hot water coming from the domestic coil to a safe
level.

e tempering valve may be obtained from

your Legacy Stoves dealer, local plumber or
plumbing supply.

is will also ensure a constant

water temperature at the tap. If hot water is
supplied to an automatic dishwasher, a line can be
run directly to this appliance ahead of the tempering
valve. Be sure to check maximum water
temperature capability of the dishwasher before
installing water-feed lines to a dishwasher in this
manner.

ere are three methods for plumbing the

domestic coil. One way is to connect the coil in
series with an existing hot water heater.

- 10 -

The installation of this unit must
comply with state and local
requirements and must be
inspected by the state or local
building inspector where required.

A tempering valve should be
installed in the hot water supply line
to reduce the temperature of the hot
water to a safe level.

«
...
14
15
16
17
18
...
»

Содержание SF170




















































Отзывы:

Нет отзывов

Похожие инструкции для SF170

Vitocrossal 300 CU3A

Бренд: Viessmann Страницы: 116

Бренд: CleaverBrooks Страницы: 314

Бренд: LAMBORGHINI CALOR Страницы: 68

Econoboil 303542

Бренд: Zip Страницы: 16

Бренд: Heat Line Страницы: 61

Бренд: VOKERA Страницы: 12

Бренд: PROBOIL Страницы: 44

Бренд: Ariston Страницы: 88

Бренд: Ariterm Страницы: 28

Бренд: Wunda Страницы: 16

Бренд: Morco Страницы: 49

Brava One HE 25 ErP

Бренд: Sime Страницы: 68

Бренд: Columbia Страницы: 32

Бренд: Rapido Страницы: 52

DOMESTIC SOLID FUEL BOILER

Бренд: Stropuva Страницы: 25

Бренд: Potterton Страницы: 60

Бренд: Lattner Boiler Company Страницы: 7

Бренд: Rinnai Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды