LED Recessed Luminaire
Holstein MS, 11210051002015, steel
Holstein MW, 11210051002020, white
Instruction Manual
Ledino
LED LIGHTING
the energy saving company
We hereby confi rm that the products are in line with the regulations ‒ and in particular with the protection requirements ‒ of the European Unionʼs
directive on the harmonisation of the legislation relating to electromagnetic compability (2014/30/EU), the low voltage directive 2014/35/EU, the
directive for Energyrelated Products 2009/125/EG and the RoHS directive 2011/65/EC.
Used units must not be disposed of with household waste!
If the unit is no longer operational, every consumer is required by law to dispose of used devices separate from household waste, e. g. at a collection point
run by the communal authority borough. In this way, used devices can be recycled and waste materials disposed of in an environmentally friendly manner.
For this reason, electrical equipment is labelled with the displayed symbol.
Technical Data:
Ledino LED Recessed Luminaire
Holstein MS, 11210051002015
, steel 3000 K
Holstein MW, 11210051002020
, white, 3000 K
220-240 V AC 50/60 Hz, max. consumption 5 W
330 lumens, warm white 3000 K
PF > 0.5, CRI > 80 Ra, SDCM < 6
330 lm correspond to approx. 25 W normal bulb light
working temp. -20 up to 40 °C
38° beam angle, not dimmable
lifetime: 25,000 h, switch cycles 20,000
plastic housing, plastic diff usor
decor side: steel brushed or white painted
IP20 - no protection against water
isolation class 2, for 65 mm hole diameter
Ø: 82 mm, H: 30 mm, 0.07 kg
statutory warranty 2 years
energy class A+, 5 kWh/1000
Spitzahornweg 1, 14974 Ludwigsfelde/ Berlin, Germany
Ledino
Deutschland GmbH
the energy saving company
①
②
③
④
L
black,
brown, grey
N
blue
IMPORTANT:
Read all instructions carefully. Only use the unit as described in these instructions. Any other use will be deemed as not
in accordance with the instructions and may lead to damage to property or even injury to persons. The manufacturer
accepts no liability for damage caused by use not in accordance with the instructions.
If you do not understand this instruction, contact your dealer.
Check the device for transport damage. Those has to be reported to the forwarder/carrier.
SAFETY:
Risk of electric shock! Electrical shock can may result in serious injury or death.
Defi cient electrical installation or excessive mains voltage may result in an electrical shock.
The fl oodlight is only suitable for use with a power supply voltage of 220 V‒240 V AC 50/60 Hz
The wiring must run according to local statutory regulations and guidelines.
All work must be carried out only by a qualifi ed electrician.
Do not install the light in near of open fi re, damp, wet areas or very hot areas.
Before drilling or sawing, make sure that no power, water or gas lines are present where the light is to be mounted.
WARNING:
Disconnect power during installation and before servicing. These procedures should only be performed by a qualified electrician.
Do not look directly into the fl oodlight, when it is switched on.
Never perform maintenance or cleaning while electric tension is not de-energized.
Use only water with dishwashing liquid and soft cloths for cleaning.
For your own protection, please wear protective goggle and dust mask.
Disconnect the power supply for the supply line!
fi g. 1:
Drill or saw a hole (Ø 65 mm) in the mounting
surface. Lay the the cable to the hole.
fi g. 2/3:
Prepare the cable in according to statutory
regulations. Loosen the 4 screws of the junction
box and remove the cap. Connect the cable
according to the marking. Screw on the cap
again.
fi g. 4:
Lift spring clamps and insert the lamp housing
into hole.
Switch on the power supply.
