Lectrosonics DR Receiver/DB Transmitter Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 28

Lectrosonics DR Receiver/DB Transmitter Скачать руководство пользователя страница 13

DSW Digital Wireless System

Rio Rancho, NM

13

Software Installation

The supplied software for the DSW system is

available on disk or downloaded from the web

site at:
www.lectrosonics.com/wdsupport

The software will run on Windows or Mac computers.

The procedure for installing it varies between down-

loaded and disk versions.

Windows Installation

NOTE: Uninstall any previous version before

installing this software.

Disk Installation:
The installation procedure is straightforward following

the on-screen instructions. Insert the disk into a local

drive. If the installer does not launch automatically,
When the first screen appears, click on

Install Wire-

less Designer Software/USB Driver.

Click on

Install Wireless Designer to launch the

installer.

After a few moments, the Setup Wizard will appear.

Click on

Next to continue.

Installation with downloaded file:

A screen listing the components to be installed will ap-

pear. All three boxes should be checked, then click on

Install to continue.

When the License Agreement screen appears, click

on

I agree and the installation will proceed. When the

installation is complete, a confirmation screen will ap-

pear. Click on

Finish, wait a moment and then remove

the disk from the drive.

«
...
11
12
13
14
15
...
»

Содержание DR Receiver/DB Transmitter





























Отзывы:

Нет отзывов