Lectric XP Lite Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 55

Lectric XP Lite Скачать руководство пользователя страница 7

LECTRICEBIKES.COM | 602.715.0907

7

WARNING!

Helmets

•

Always wear a helmet. Wearing a helmet properly may reduce the

risk of a severe head injury.

When riding, always wear a helmet that

meets or exceeds the standards of the Consumer Product Safety

Commission (CPSC). Check the manual that comes with your

helmet.

• Ensure your helmet fits your head and is properly secured. If you

attach a child’s seat to the bicycle, the child must wear a properly

fitted helmet at all times.

•

Read your helmet manual to make sure it is adjusted properly

according to the fitting instructions provided by the helmet

manufacturer.

• A proper-fitting helmet should be comfortable and should neither

rock forward/backward nor side to side.

• Refer to the tightening torque section (p.19) of this manual in

order

to properly torque the chain tensioner and make sure it

is in the

correct position for proper function. If the chain is too tight and you
are walking the bike in PAS 1-5, the front chainring and pedals will
move which will cause PAS to activate. The acceleration from this
activation could cause a crash. To avoid this, walk the bike in PAS 0.

Pre-Ride Safety Check

•

Before each ride, inspect your eBike for damage. If damage is

found, do not ride.

•

Verify that the front and rear axles are secure.

•

Verify that the handlebar and seat clamps are closed and

tightened to the torque specified in the Owner’s Manual.

•

Verify that both the handlebar latch and frame latch are secure

and fully closed.

•

Check tire pressure of both wheels.

•

Pull the brake levers to ensure the brakes are working properly

and adjust if necessary.

•

NEVER exceed the maximum total weight limit of 275 lbs. (125

kg).

The rear rack can hold a maximum of 55 lbs. (25 kg). As an

example, if you have 40 lbs. (18 kg) of cargo, then the maximum

weight of the rider would be 235 lbs. (107 kg)

«
...
5
6
7
8
9
...
»

Содержание XP Lite
























































Отзывы:

Нет отзывов