2.3 Correct use and Operation
4
For safety reasons, this appliance may only be used after
it has been installed.
Reliable and safe operation of this appliance can only be
assured if it has been connected to the main electricity
supply.
Before using the appliance, ensure that all packaging
materials are removed from the appliance and make
sure that the connection data on the data plate [voltage
(V) and frequency (Hz)] indicated on the appliance
corresponds to the voltage and frequency of the power
supply in your household. Consult a qualified electrician
if in doubt.
D
Cracks, fissures or fractures in the panels can damage the
underlying electronics. Switch off and disconnect the
appliance immediately.
After the cooler is put into operation, never touch its inner
surface, especially when your hand is wet; otherwise
the skin may stick onto the inner surface to get injured.
O NOT store or spray flammable materials in the
appliance or near this appliance while it is in operation
(e.g. aerosols).
WARNING
Regularly clean surfaces that can come in contact with
food and accessible drainage systems. If the refrigerating
appliance is left empty for long periods, switch off,
clean, dry, and leave the door open to prevent mould
developing within the appliance.
Opening the door for long periods can cause a significant
increase of the temperature in the compartments of the
appliance.
The refrigerant isobutane (R600a) is contained within the
refrigerant circuit of the appliance, a natural gas with a
high level of environmental compatibility, which is
nevertheless flammable. During transportation and
installation of the appliance, ensure that none of the
components of the refrigerant circuit becomes damaged.
2.4 Disassembling and Disposal of the
Appliance
2.5 Accessories and Spare parts
(see the “Environmental Tips” section for best practices on
disposing of this appliance).
The device must only be disassembled by trained
specialists who are familiar with and comply with the
standard national regulations and supplementary
regulations of the local utility companies.
Work on electrical components must only be conducted by
trained electrical personnel.
Incorrect components can lead to personal injury or
damage to the appliance. Only use original Lecavist spare
parts for repairs.
Modifications, additions or alterations to the appliance
can lead to safety risks. If spare parts or accessories from
other manufacturers are used, the warranty will be
invalidated, and Lecavist cannot accept liability.
Please check
www.lecavist.com
for more information.
www.lecavist.com
3. INSTALLATION INSTRUCTIONS
Before Using Your Wine Cooler
Remove the exterior and interior packing.
Before connecting the Wine Cooler to the power
source, let it stand upright for approximately 2 hours.
This will reduce the possibility of a malfunction in the
cooling system from handling during transportation.
Clean the interior surface with lukewarm water using
a soft cloth.
Install the handle on the left side of the door.
Defrosting:
While running, wine cooler has got one time defrosting
process every 8 hours and defrosting will last about 30
minutes. The defrosting water will collected in the drip
tray before evaporating.
At this process, the temperature display may be higher
than the setting temperature.
Installation of Your Wine Cooler
This appliance is designed for free standing or built-in
(full recessed) installation.
Place your Wine Cooler on a floor that is strong enough
to support it when it is fully loaded. To level your Wine
Cooler, adjust the front leveling legs at the bottom of
the Wine Cooler.
Locate the Wine Cellar away from direct sunlight and
sources of heat (stove, heater, radiator, etc.). Direct
sunlight may affect the acrylic coating and heat sources
may increase electrical consumption. Extreme cold
ambient temperatures may also cause the unit not to
perform properly.
Avoid locating the unit in moist areas.
Plug the Wine Cooler into an exclusive, properly installed-
grounded wall outlet. Do not under any circumstances
cut or remove the third (ground) prong from the power
cord. Any questions concerning power and/or grounding
should be directed toward a certified or an authorised
products service center.
Prevent water ingress. Never sprinkle or flush the cooler
using water, place the cooler in an area exposed to
moisture or water sprinkling, or fill the cooler
with water, so as to avoid impairment of the electric
insulation of the cooler. Furthermore, failing to follow
such requirements may lead to electric shock and fire,
or other accidents.
