Lear Siegler BOGEN Acousta-Master CT 100 Скачать руководство пользователя страница 8

When replacing the output transistors, clean all foreign

matter from the heat sink, insulator, and transistor. Brush a
generous amount of silicon compound such as Dow Corning
No. 340 to completely cover both surfaces of the insulator
(Part No. 16-9278-01). Place the insulator between the heat
sink and the replacement transistor. Use the original transis-
tor mounting hardware to mount the replacement transis-
tor.

The above procedure may require some dismantling of

the heat sink. It is therefore important to also clean the
contact surface of the thermal breaker and to apply the
silicon compound to the thermal breaker before reassem-
bling the heat sink. Make certain the thermal breaker makes
firm contact with the heat sink.

REPLACEMENT PARTS

Most components used in the amplifier are standard

parts available through reputable parts suppliers. The parts

listed here may be obtained from  Bogen   d i s t r i b u t o r s ,

service agencies or directly from the factory. When ordering
a part, specify a part number, the model of the unit, and
give the series designation, which is a letter followed by

numbers, printed on the chassis. For parts on circuit
boards, also give the component board assembly number,
which begins with “45”.

When replacing transistors, use those made by the

specified manufacturers. Transistors from other suppliers
may not be satisfactory. Certain resistors must be Allen-

Bradley products. These are designated by “AB” on the
schematic diagram.

Ref. No. Part No. Description

A3 45-9813-01
C3,19

79-008-049

C5, 17,18 79-008-057
Cl5

79-504-032

C25

79-l 12-001

c 2 9   79-008-058
c31

79-008-062

CRl, 2, 6 96-5333-01
CR3 96-5344-04
CR4

96-5344-02

CR5 96-5202-01
Ll-3 95-5 162-01
L4

95-5 163-01

95-5164-01 96-5213-01
96-5346-01
96-5 96-5298-01 176-01

Q10

96-5283-01

Q11

96-5357-01

Q12

96-5356-01

Rl

77-001-712

R23 77-00 l-709
R32 77-001-722

R48 75-842-561
R65, 69 76-107-096
R67, 68 76-116-003

PC board assembly

Capacitor, electrolytic, 500µF, 35V
Capacitor, electrolytic, 50µF, 50V
Capacitor, tantalum, 2.2µF, 15V
Capacitor, electrolytic, 500µF, 75V
Capacitor, electrolytic, l0µF, 50V
Capacitor, Electrolytic, 1 OOµF, 50V
Diode, 400 piv @ 1 A
Diode, zener, 18V, 2W

Diode, zener, 12V, 2W

H V R 3
Inductor, 150µH
Inductor, 50µH
Inductor, 1 5µH

Transistor, 2N5089  or
Transistor, BC 239C
Transistor, MPS-65 18
Transistor, SPS-1910

Transistor, MPS-A55
Transistor, 2SD-389  (P)
/2SD313D/TIP31A
Transistor, 2SB-5  12 (P)
/2SB507D/TIP32A

Control, aux vol., 2 megohm
C.T.
Control, comp., 50 kilohm
Control, master vol., 10
kilohm

Resistor, 560 ohm, 3W
Resistor, .82 ohm, 2W
Resistor, .27 ohm, 7W

Schem.  Ref. Part No. Description

Chassis electrical components

C l 0 6

79-509-05  1

Cap, electrolytic, 1500µF,

79-509-052

79-509-053

C l 0 7   79-509-O 15

79-509-O 17

79-509-O 19

CBlOl

94-00 17-04

94-00 17-09

94-00 17-15

CB-102 94-00 14-07
CR-101, 102 96-5241-01
CR-103, 104 96-5333-01
1101 94-0302-05
QlOl-106

96-5385-01

96-5397-01

RlOl-105
R108
R109,  110

SW101

TlOl

77-001-723
75-741-101
76-116-003

T102

81-003-057
81-003-053
83-805-000
83-804-000
83-803-000
83-422-000
83-423-000
83-424-000

75V (CT-35)
Cap, electrolytic, 2000µF,
75v (CT-60)
Cap, electrolytic, 3000µF,
75V (CT-l00)
Cap, electrolytic, 750µF,

5OV  (CT-35)

Cap, electrolytic, 1500µF,

5ov (CT-60)
Cap, electrolytic, 2500µF,
50V (CT-l00)
Circuit breaker, .93A hold
(CT-35)
Circuit breaker, 1.65A  hold
(CT-60)
Circuit breaker, 2.5A hold
(CT-l 00)
Thermal breaker, 105°C
Diode, 300 piv @ 3A
Diode, 400 piv @ 1A
Pilot lamp assembly
Transistor, 2N3055H  RCA
(CT-35,60)
Transistor, 2N3055  Solitron
(CT-l 00)
Control, slide, 500 kilohm   __
Resistor, 100 ohm, 7W
Resistor, .27 ohm, 7W
(CT-l 00)
Switch, ac, 3A (CT-35,60)
Switch, ac, 6A (CT-l00)
Transformer, power (CT-35)
Transformer, power (CT-60) 
Transformer, power (CT-l00)
Transformer, output (CT-35)
Transformer, output (CT-60)
Transformer, output (CT-l00)

Pre-amp board components

Al, A2
C4,13

Q1,2

45-7082-01 

PC board assembly

79-008-05 1 Cap, electrolytic, 2 5 µ F 35V
96-5213-01 Transistor, 2N5089  or
96-5346-01 Transistor, BC 239C

Rl,

 2,

 15, 16 76-147-126 Resistor, 4.7 ohm, 1/2W

R14,25

77-001-711 Control, 1 megohm

Mechanical components

03-0628-02 

Control, anti-feedback

03-0593-01 Control, aux 1, 2 vol.
03-0641-01 Control, mic 1, 2 vol.

03-0592-01 Control, master vol., comp.,

mic 3,4

Содержание BOGEN Acousta-Master CT 100











Отзывы: