LeapFrog LF815-0HD Скачать руководство пользователя страница 17

Страница: 17 / 23

FCC Part 15

This  equipment  has  been  tested  and  found  to  comply  with
the requirements for a Class B digital device under Part 15 of
the Federal Communications Commission (FCC) rules. These
requirements  are  intended  to  provide  reasonable  protection
against harmful interference in a residential installation. This
equipment  generates,  uses  and  can  radiate  radio  frequency
energy  and,  if  not  installed  and  used  in  accordance  with
the  instructions,  may  cause  harmful  interference  to  radio
communications.  However,  there  is  no  guarantee  that
interference  will  not  occur  in  a  particular  installation.  If
this  equipment  does  cause  harmful  interference  to  radio  or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase  the  separation  between  the  equipment  and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

WARNING: Changes or modifications to this equipment not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.

To ensure safety of users, the FCC has established criteria for the
amount of radio frequency energy that can be safely absorbed
by a user or bystander according to the intended usage of the
product. This product has been tested and found to comply

with the FCC criteria. The Baby Unit shall be installed and used
such that parts of all persons’ body are maintained at a distance
of approximately 8 in (20 cm) or more. The transmitter and
antenna of the Parent Viewer shall be held at least 1 in (2.5 cm)
from your face.

This Class B digital apparatus complies with Canadian
requirement: CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This

device

contains

licence-exempt

transmitter(s)/

receiver(s) that comply with Innovation, Science and Economic
Development  Canada’s  licence-exempt  RSS(s).  Operation
is  subject  to  the  following  two  conditions:  (1)  This  device
may  not  cause  interference.  (2)  This  device  must  accept  any
interference,  including  interference  that  may  cause  undesired
operation of the device.
The term ‘’IC:‘’ before the certification/registration number only
signifies that the Industry Canada technical specifications were
met.
This  product  meets  the  applicable  Innovation,  Science  and
Economic Development Canada technical specifications.

RF radiation exposure statement

The product complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment. The Baby Unit should
be installed and operated with a minimum distance of 8 in (20
cm) between the Baby Unit and all persons’ body. Use of other
accessories may not ensure compliance with FCC RF exposure
guidelines. This equipment complies also with Industry Canada
RSS-102 with respect to Canada’s Health Code 6 for Exposure
of Humans to RF Fields.

FCC and IC regulations

Disclaimer and Limitation of Liability

LeapFrog and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook.
LeapFrog and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of
this software. LeapFrog and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a
result of malfunction, dead battery, or repairs. Be sure to make backup copies of important data on other media to protect
against data loss.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

CAN ICES-3 (B)/NMB-3(B)

Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Warranty:

Please visit our website at leapfrog.com for full details of the warranty provided in your country.

The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating
in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out
of service within the United States and Canada. The program provides a convenient alternative to placing
used Li-ion batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the
program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY

for information

on Li-ion battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its
commitment to protecting our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

The RBRC seal

Mesures de sécurité importantes

La plaque signalétique appliquée est située au bas du socle de

l’unité du bébé.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre

certaines mesures de précaution de base afin de réduire les

risques d’incendie, d’électrocution et de blessures corporelles,

dont ceux qui suivent :

Observez toutes les instructions et mises en garde inscrites

sur l’appareil.

L’installation par un adulte est requise.

MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur

supérieure à 2 mètres.

Ce produit ne remplace pas la surveillance adulte du nourrisson.

La supervision du nourrisson est la responsabilité du parent

ou de la personne qui s’occupe de l’enfant. Ce produit pourrait

cesser de fonctionner et, par conséquent, vous ne devriez pas

présumer qu’il continuera de fonctionner correctement pendant

une période de temps donnée. De plus, il ne s’agit pas d’un

instrument médical et ne devrait pas être utilisé comme tel. Ce

produit est destiné à vous aider à superviser votre bébé.

N’utilisez pas cet appareil près de l’eau ni de toute autre

source d’humidité, par exemple, près d’une baignoire, cuve

à lessive, évier de cuisine, dans un sous-sol humide ni près

d’une piscine, dans un soussol humide ou une douche.

MISE EN GARDE: Utilisez uniquement la pile fournie. Un

risque d’explosion pourrait survenir si un mauvais type de

pile est utilisé pour l’unité du parent. La pile ne peut pas être

soumise à des températures extrêmes élevées ou basses et à

une faible pression d’air à haute altitude pendant l’utilisation,

l’entreposage ou le transport. L’élimination de la pile dans le

feu ou dans un four chaud, ou l’écrasement ou le découpage

mécanique de la pile peuvent entraîner une explosion. Laisser

la pile dans un environnement à température extrêmement

élevée peut entraîner une explosion ou la fuite d’un liquide ou

d’un gaz inflammable. Une pile soumise à une pression d’air

extrêmement basse peut provoquer une explosion ou une

fuite de liquide ou de gaz inflammable. Éliminer la pile usagée

conformément aux informations du Sceau RBRC.

N’utilisez que les adaptateurs inclus avec ce produit.

L’utilisation d’un adaptateur dont la polarité ou la tension

serait inadéquate risque d’endommager sérieusement le

produit et mettre votre sécurité en péril.

Informations sur les adaptateurs électriques :

Adaptateur de l’unité du parent : Sortie : 5V DC 2A

VTech Telecommunications Ltd.

Modèle: VT07EUS05150

Adaptateur de l’unité du bébé : Sortie : 5V DC 1A

VTech Telecommunications Ltd.

Modèle: VT05EUS05100

Informations sur les piles rechargeables :

Zhuhai Great Power Energy Co., Ltd.

Lithium battery, 3.7V 5000mAh;

Modèle: GSP806090-5Ah-3.7V-1S1P

Lorsqu’ils sont branchés dans une prise de courant, les

adaptateurs secteur ont été conçus pour être orientés

correctement, soit à la verticale ou au plancher. Les broches

n’ont pas été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici est branché

dans une prise au plafond, sous une table ou dans un meuble.

Pour les PRODUITS À BRANCHER À UNE PRISE DE

COURANT, la prise de courant doit être installée près du

produit, afin d’assurer une accessibilité sécuritaire à la prise

de courant.

10. Débranchez ce produit de la prise de courant avant de

procéder au nettoyage. N’utilisez pas de nettoyants en

aérosols. Utilisez un chiffon humide pour le nettoyer.

11. Ne coupez pas les cordons d’alimentation pour remplacer les

fiches, car ceci peut présenter un danger potentiel.

12. Ne laissez aucun objet reposer ni appuyer sur le cordon

d’alimentation. N’installez pas cet appareil dans un endroit

où l’on risque d’écraser le cordon d’alimentation ou de le

piétiner.

13. Ne faites fonctionner cet appareil qu’avec le type

d’alimentation indiqué sur l’étiquette. Si vous ne connaissez

pas le type d’alimentation que vous possédez à votre

domicile, consultez votre marchand ou votre compagnie

locale d’électricité.

14. Ne surchargez pas les prises de courant murales ni les

rallonges électriques.

15. Ne placez pas cet appareil sur un chariot, meuble, trépied,

support de montage ni table chancelants.

16. Les trous et ouvertures du boîtier, situés à l’arrière de

l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour

l’empêcher de surchauffer, ne bloquez sous aucun prétexte

ces ouvertures et n’empêchez pas l’aération adéquate de

l’appareil en le plaçant sur un lit, divan, tapis ou toute autre

surface similaire. De même, ne le positionnez pas à proximité

ni au-dessus d’une source de chaleur ou d’un calorifère. De

plus, ne placez pas l’appareil dans un endroit avant de vous

assurer qu’il y ait une bonne circulation d’air.

17. N’enfoncez jamais d’objets à travers les ouvertures de cet

appareil, car ils pourraient entrer en contact avec des points de

tension dangereux ou causer des courts-circuits qui peuvent

dégénérer en incendies ou en risques d’électrocution. Ne

renversez jamais de liquide dans ce produit.

18. Afin de réduire les risques d’électrocution, ne démontez

pas cet appareil, mais apportez-le dans un centre de service

autorisé. L’ouverture du boîtier ou le retrait de toutes pièces

que contient cet appareil, à l’exception de l’accès autorisé

à certaines portes ou ouvertures, risque de vous exposer à

des points de tension dangereux ou d’autres dangers. Un

remontage incorrect peut par la suite présenter des risques

d’électrocution.

19. Vous devriez tester la réception chaque fois que vous mettez

l’appareil en fonction.

20. Examinez les composantes afin de vérifier si celles-ci ne sont

pas endommagées.

21. Il existe un très faible risque de perte de confidentialité

avec certains appareils électroniques (autres écoute-bébés,

téléphones sans fils etc.). Pour l’éviter, s’assurer que le

produit n’a jamais été utilisé avant l’achat, réinitialiser l’unité

de façon périodique, éteindre l’écoute-bébé quand il n’est

pas en cours d’utilisation.

22. Les enfants devraient être supervisés afin de vous assurer

qu’ils ne jouent pas avec l’appareil.

23. Le produit n’est pas conçu pour être utilisé par des personnes

(incluant des enfants) aux capacités physiques, sensorielles

ou mentales réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné suffisamment

de supervision ou d’instructions relativement à l’utilisation de

l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

Utilisez et entreposez le produit à une température entre 0˚

C (32˚F) et 40˚C (104˚ F).

N’exposez pas cet appareil à des froids ou des chaleurs

extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez

pas près d’une source de chauffage.

Le bloc-piles ne doit pas être exposé à la chaleur excessive

telle que la lumière du soleil ou au feu.

Avertissement - Risque de strangulation

- Les enfants se sont ÉTRANGLÉS dans des

cordons. Gardez ce cordon hors de portée des

enfants (à plus de 0,9 m). N’enlevez pas cette

étiquette.

Ne jamais placer le moniteur à l’intérieur du berceau ou du

parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s)

portative avec un article tel une serviette ou une couverture.

D’autres équipements électroniques peuvent produire des

interférences sur votre moniteur vidéo et audio. Tentez

d’installer votre moniteur vidéo ou audio à l’écart des appareils

électroniques tels que des routeurs sans fil, radios, téléphones

cellulaires, interphones, moniteurs, téléphones, ordinateurs

personnels, électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs

numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’,

une firme de recherche indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les téléphones sans

fil portatifs et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des aliments et

drogues (FDA) des États-Unis, la firme WTR recommande aux

médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à au moins six

pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil directement sur

le stimulateur cardiaque, tel que dans une poche de chemise,

lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque

pour les détenteurs de simulateurs cardiaques causés par les gens

qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)

Ce produit de LeapFrog est conforme à toutes les normes se

rapportant aux champs électromagnétiques (EMF) standard. Si

vous le manipulez correctement en suivant les instructions de

ce guide, son utilisation sera sécuritaire pendant de nombreuses

années, selon les meilleures évidences scientifiques dont nous

disposons aujourd’hui.

For cETL compliance only

Night Light

Night Vision (B&W and Color)

When the Baby Unit being viewed detects
low light levels, the infrared LEDs switch on
automatically with the activiation of the B&W
Night Vision mode. Baby Unit has infrared LEDs
that allow you to see your baby clearly at night
or in a dark room.
When Black and White Night Vision mode is
activated,

appears on the screen. When

Color Night Vision mode is activated,

appears on the screen.

Notes:

• It is normal to see a short white glare on your Parent

Viewer screen as the Baby Unit is adapting to the
dark environment.

• If you adjust the night vision mode while night vision

is not activated, the new settings will be saved and
applied the next time it activates.

Change your night vision viewing mode

1. Press the

Night Mode quick set key

to view the Night Mode menu.

2. Press or to choose

for

black-and-white night vision viewing or

for color night vision viewing.

Select Patrol mode as your monitoring
mode to alternately view the image from
Baby Units

and

every 10

seconds.

Patrol mode

Select Split mode as your monitoring mode to view the images from
both Baby Units at the same time.

Note:

• While in Split mode, you can press

to highlight the view of the

Baby Unit 1

or Baby Unit 2

, and hear the sounds transmitted from the

highlighted Baby Unit.

Split mode

Monitoring mode

Single CAM mode

Select Baby Unit 1

or Baby Unit 2

view the image from the selected Baby Unit.

The Parent Viewer display will dim to conserve energy after 5 minutes of inactivity, in which
there were neither any key pressed nor alert received from the Baby Unit.

Night Vision
Mode

Description

B&W Night Vision

Suitable for extremely dark or low
light environments.
Images will be in black-and-white.

Color Night Vision

Suitable for low-light room
conditions with night light as an
assisting light source.
Images will be in color.

Dim Mode

For LF815-2HD and Pairing with LF815-0HD Only

Adjust the night light on the Parent Viewer

1. Press the

Night Mode quick set key

to view the Night Mode menu.

2. Press

to brighten the night light (or turn on

the night light when it is switched off).
Press

to dim the night light (or turn off the

night light when it is at the lowest brightness
level).

1. Press to enter the main menu.

2. Press again to select

3. Press and to select

, press .

4. Press and to choose the desired

brightness level, then press to confirm
your selection.

Want a softer hue from the Baby Unit’s night light to relax your little one? You can control the brightness
of its glow remotely from your Parent Viewer, or directly on the Baby Unit.

1 2

Adjust the night light on the Baby Unit

•

Tap the

Night light control key

located

on the top of the Baby Unit to turn on/off the
night light.

•

Tap and hold the

Night light control key

to adjust the night light’s brightness. It

changes level by level at a time.

There are 5

levels in total.

- OR -

Tip:

• The video quality may vary depending on the

surrounding environment and interfering factors like
lightings, objects, colors and backgrounds. Adjust the
Baby Unit’s angle or place the Baby Unit at a higher
elevation to prevent glare and blurry displays.

Note:

• If Auto Brightness has been pre-selected, any adjustment in night light brightness (either on the Baby Unit or

the Parent Viewer) will automatically turn off Auto Brightness mode and switch to the fixed level of brightness.

Troubleshooting

Symptom

Try this

Why does the baby

monitor not respond

normally?

Try the following (in the order listed) for a common cure:

1. Disconnect the power to the Baby Unit(s) and the Parent Viewer.

2. Wait a few seconds before connecting power back to the Baby Unit(s) and the Parent Viewer.

3. Turn on the Baby Unit(s) and the Parent Viewer.

4. Wait for the Parent Viewer to synchronize with the Baby Unit(s). Allow up to one minute for this

to take place.

Why doesn’t the Baby

Unit’s and Parent

Viewer’s power LED turn

on when I switch on the

units?

The Parent Viewer may not be connected to power. Insert the appliance plug into the power jack

of the Parent Viewer and put the adapter in a wall socket. Then, press the

Power

button on the

Parent Viewer to establish connection with the Baby Unit.

The Baby Unit may not be connected to power. Insert the appliance plug into the power jack of the

Baby Unit and put the adapter in a wall socket. Then, slide the On/Off switch on the Baby Unit to

establish connection with the Parent Viewer.

Why are my images in

black and white?

The images are in black white during night-time or in a dark room when night vision is

automatically activated. You can also choose to view your baby at night in color, see

Night Vision

(B&W and Color)

to learn how.

Why is the Baby Unit

producing a high-pitched

noise?

The Parent Viewer and Baby Unit(s) may be too close to each other.
• Move the Parent Viewer away from the Baby Unit(s) until the noise stops (OR)
• Turn down the volume of your Parent Viewer.

Why does the Parent

Viewer beep?

The Baby Unit(s) may be out of range. Move the Parent Viewer closer to the Baby Unit(s) (but not

less than 3 feet).

The Parent Viewer may not have enough battery for the Parent Viewer to perform normally.

Charge the Parent Viewer until the battery icon becomes solid

The temperature of your baby’s room may be too high or too low.

Why can’t I hear any

sounds from the Parent

Viewer? Why can’t I

hear my baby cry?

The Parent Viewer speaker volume may be too low or muted. Press

to open the volume

adjustment menu, then press to increase the speaker volume. Or you can use the Parent Viewer

menu to change the Parent Viewer’s sound sensitivity to the highest level (level 5), see

Sound

Detection and Auto Wake Up.

Why can’t I establish a

connection? Why does

my connection cut off

every now and then?

Why are there sound

interruptions?

The Baby Unit(s) may be out of range. Move the Parent Viewer closer to the Baby Unit(s) (but not

less than 3 feet).

Other electronic and wireless products may cause interference with your baby monitor. Try

installing your baby monitor as far away from these devices as possible.

If you powered on only one Baby Unit but have two paired to the Parent Viewer, your Parent

Viewer may display

and the LINK LED light flashes. Switch to the Baby Unit you have

turned on via the menu.

Instructions for Care

FOR INDOOR, DRY-LOCATION USE ONLY.
To keep this product in good condition, follow these guidelines:

•

Avoid putting it near heating appliances and devices
that generate electrical noise (for example, motors or
fluorescent lamps).

•

Do not spill liquid of any kind on this product or
immerse the product in water as it may render it
inoperative.

•

Clean with a slightly damp cloth in cold water (do not
use soap, detergent, or other chemicals)

•

Keep food and beverages away from this product.

•

Make sure the product is dry before you connect it to
the power source again.

•

Never try to dismantle the unit.

•

Avoid prolonged exposure to extreme temperatures
and direct sunlight or moisture.

•

Avoid dropping the product or treating it roughly.

Visit our Consumer Support website 24 hours a day at:

U.S.:

leapfrog.com/support

C.A.:

leapfrog.ca/support

Or call our

Customer Service number:

1 (800) 701-5327 in the U.S. and Canada during Customer Service hours

Monday to Friday, 9am - 6pm Central Time

Customer Support

7 0

2 5.5°C

25.5°C

7 0

2 5.5°C

Mount the Baby Unit on a dry wall (optional)

1. Place the wall mount bracket

on a wall and then use a
pencil to mark the top and
the bottom holes as shown.
Remove the wall mount
bracket and drill two holes in
the wall (7/32 inch drill bit).

Notes:

• Check for reception strength and the Baby Unit’s viewing angle before drilling the holes.
• The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the

screws and anchors separately to mount your Baby Units.

2. If you drill the holes into a stud, go

to step 3.

•

If you drill the holes into an object
other than a stud, insert the wall
anchors into the holes. Tap gently
on the ends with a hammer until
the wall anchors are flush with the
wall.

3. Align the wall mount

bracket and screws with
the holes in the wall as
shown. Tighten the screw
in the middle hole first,
so that the wall mount
bracket position is fixed.
You can tighten the other
screw in the top hole.

3. Insert the screws into

the holes and tighten
the screws until only 1/4
inch of the screws are
exposed.

4. Place the Baby Unit on

the wall mount bracket.
Tighten the screw into
the threaded socket at
the bottom to secure
the Baby Unit. Align
the holes on the wall
mount bracket with the
screws on the wall, and
slide the wall mount
bracket down until it
locks into place.

5. You can maximize your Baby Unit’s

viewing angles by tilting the wall mount
bracket.
Hold the Baby Unit, and then rotate
the knob in an anti-clockwise direction.
This will loosen the joint of the wall
mount bracket.
Tilt your Baby Unit up or down to adjust
to your preferred angle. Then, rotate
the knob in a clockwise direction to
tighten the joint and secure the angle.

4. Place the Baby Unit on

the wall mount bracket.
Tighten the screw into
the threaded socket at
the bottom to secure the
Baby Unit.

Step

Download the free LeapFrog baby
monitor mobile app and install it to a
mobile device, then use your mobile
device and the mobile app to monitor
your areas remotely.

1. Press

MENU

when the Parent Viewer is in idle.

2. Go to

Connect Mobile Phone

3. Scan the QR code in the Parent Viewer to

download the app into your mobile device.

4. Follow the instructions in the mobile app to set

up and pair your Baby Unit to the mobile app.

Alternatively, you can download the mobile app
from the App Store or Google Play store.

Install the mobile app

1. Browse the App Store

or the Google Play

store

2. Download and install the free LeapFrog mobile

app to your devic

-OR-

Scan the QR code below to get the app.

Note:

• Make sure your mobile device meets the

minimum requirement for the mobile app.

Minimum requirements:

The mobile app is compatible with:
• Android

5.0 or later; and

• iOS 11.0 or later.

Step

After installing the mobile app, follow the
instructions in the mobile app and Parent Viewer
to set up and pair your Baby Unit.

In your mobile device:

1. Tap the app icon to run the mobile app in

your mobile device, and then create a user
account.

2. We recommend that you use common

webmail services, such as Google Gmail, for
the registration of your user account. Check
your email (and Spam folder), and activate
your new user account via the email link
Then, sign in to your account.

3. Follow the instructions in the mobile app to

pair the camera. Tap

, then in the mobile

app to get started.

Download app for mobile access

To ensure that your baby monitor is always at its best performance, the Parent Viewer will
prompt a message and ask you to update its software and the Baby Unit's firmware when there
are new versions available.
• Follow the instructions on the Parent Viewer screen to update your baby monitor.

To check if your device is running on the latest software, or to update your device software, go to:

> Software Update

Connect your baby monitor to Wi-Fi

• You must connect your baby monitor to your secured home Wi-Fi network in order to receive

the latest software and firmware updates. To set Wi-Fi up, go to:

> Configure Wi-Fi > Change Wi-Fi Networks.

Auto software and firmware update

Basic Operation - Parent Viewer

Adjust Parent Viewer’s speaker volume

1. Press

to open the volume adjustment

bar.
2. Press to increase the speaker volume
and to decrease the speaker volume.

Talk to your baby via the Baby Unit

1. Press and hold the

key.

2. When the

icon displays on the screen,

speak to your Parent Viewer. Your voice is
transmitted to the Baby Unit.

3. When finished talking, release the

key

and hear your baby again.

Zoom

Press

to zoom in or out. The zoom

sequence is

, then

Turn on/off the Parent Viewer screen

You can turn on or off the Parent Viewer
screen without powering off the Parent Viewer.
You will still be able to hear sounds from the
Baby Unit.
• Press on the Parent Viewer to turn off

the screen.

• Press any key on the Parent Viewer to turn

on the screen again.

Use the menu

Press to enter the menu, choose a menu
item, or save a setting. You can use the Parent
Viewer for advanced settings or operations,
such as to play or stop the Baby Unit’s lullaby,
or to adjust the Baby Unit sound sensitivity.

While in the menu:
• Press , , , or to scroll among the

menu options.

• Press to select an item, or to save a

setting.

• Press

/ to return to the live video.

• Press

to go to the

Help & Info

page.

26°C

Monitoring mode

Exit

Select

1 2

Help

7 0

2 5.5°C

7 0

2 5.5°C

Press and hold

7 0

2 5.5°C

LeapFrog cares about your privacy and peace of mind. That’s why we’ve put together a list of industry-

recommended best practices to help keep your wireless connection private and your devices protected

when online. We recommend you carefully review and consider complying with the following tips.

Ensure your wireless connection is secure.

• Before installing a device, ensure your router’s wireless signal is encrypted by selecting the

“WPA2-PSK with AES” setting in your router’s wireless security menu.

Change default settings.

• Change your wireless router’s default wireless network name (SSID) to something unique.
• Change default passwords to unique, strong passwords. A strong password:

-  Is at least 10 characters long.
-  Is complex.
-  Does not contain dictionary words or personal information.
-  Contains a mix of uppercase letters, lowercase letters, special characters and numbers.

Keep your devices up to date.

• Download security patches from manufacturers as soon as they become available. This will ensure

you always have the latest security updates.

• If the feature is available, enable automatic updates for future releases.

Disable Universal Plug and Play (UPnP) on your router.

• UPnP enabled on a router can limit the effectiveness of your firewall by allowing other network

devices to open inbound ports without any intervention or approval from you. A virus or other
malware program could use this function to compromise security for the entire network.

For more information on wireless connections and protecting your data, please review the following
resources from industry experts:
1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips –

www.fcc.gov/consumers/guides/how-protect-yourself-online.

2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet –

www.us-cert.gov/ncas/tips/ST15-003.

3. Federal Trade Commission: Using IP Cameras Safely –

https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.

4. Wi-Fi Alliance: Discover Wi-Fi Security –

http://www.wi-fi.org/discover-wi-fi/security.

Protect your privacy and online security

Parent Viewer Icons (continued)

If you plan to install your Baby Unit in a designated location,
and use your home Wi-Fi network to connect your video
monitor, you need to test which of your selected monitoring
areas within the house have good Wi-Fi signal strength.
After you have powered on your Parent Viewer, you can
check the Parent Viewer’s Wi-Fi signal strength by going to:

> Configure Wifi > Connection Status.

Adjust the distance between your Baby Unit and the Wi-Fi
router if needed. Once you have identified the suitable
location, you can install your Baby Unit.

Tip:

• Depending on surroundings and obstructing factors that affect signal strength, such as distance and internal

walls, you may experience reduced Wi-Fi signal. To improve the Wi-Fi signal strength, adjust the distance or
direction of your Parent Viewer. Check with your Parent Viewer again.

7 0

25.5°C

7 0

2 5.5°C

7 0

2 5.5°C

Test the location for the Baby Unit

Online Help

Find the answer to your questions on our Online Support page . There, you will find information
about product installation, features, operations and settings. Get assisted at your own pace with
video walk-throughs and Frequently Asked Questions.

Visit

www.leapfrog.zendesk.com

or scan the QR code on the left to enter our

Online Support page

Night light is turned on and the automatic
brightness setting is turned on.

Parent Viewer speaker is muted.

Temperature alert is turned on.

Humidity is lo

wer than 30%.

Humidity is within 30-60%.

Humidity is higher than 60%.

Temperature is lower than 68°F.