background image

Leaf LT2020E manual 

Page  18  Of  18 

LTHDMI2020E

 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the 
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

Modifications not expressly approved by the manufacturer could void the user's authority to operated the equipment under FCC 
rules. 

LTB1E: BREAKOUT 

FEATURE 

SPECIFICATION 

INPUTS: MAIN A/V 

(1x) HDBase-T Input 

. See LT2020E for further 

specification.

 

OUTPUTS: AUDIO/VIDEO 

(1x) HDMI output 

INPUT: AUDIO 

(1X) Digital coax (S/PDIF)  via RCA socket 

Audio return from RCA socket specification: 
Range: ~50 metres. Less if subjected to electrical 
interference, cable type, power supplies used  etc.

 

OUTPUTS: ETHERNET 

(1x) ETHERNET OUTPUT 

OUTPUTS:RS232 

(1x) RS-232 PORT (BLACK RJ45 CONNECTOR) Up to 115200 
Baud. 

OUTPUT: IR THROUGHPUT 

IR LED DRIVER 38KHz...  OR...  IR INPUT. (Selected by main 
unit). 3.5mm TRS female connector  

NUMBER OF INPUTS/OUTPUT 

1/1 

POWER 

Local power required 12W (1A @ 12V). 

DIMENSIONS (W,D,H) 

116mmx121mmx31mm(36mm with wall plate fitted) 

Содержание LT2020E



















Отзывы: