Leadshine EM870S Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 17

Leadshine EM870S Скачать руководство пользователя страница 7

EM870S Digital Stepper Drive User Manual

Page | 4

3.2 P2 - Fault and Brake Output Connector

Pin

Details

ALM

Output Connection: Optional.

(1)

Maximum 30V/100mA output

(2)

Sinking or sourcing

(3)

The resistance between ALM and COM- is low impedance as default (configurable by DIP

switch SW12), and will change to high when the drive goes into error protection.

(4)

Fault and Brake connection refer to

BR

COM-

3.3 P3 - Power Connector

Pin

Details

GND

Connect to power supply ground connection.

+VDC

Connect to power supply positive connection. Suggest 24-72VDC power supply voltage

!

Warning

Warning:

Don’t plug/unplug P3 o

r P4 connector

to avoid drive damage or injury while powered on.

3.4 P4 - Motor Connector

PIN

Details

A+

Connect to motor A+ wire

A-

Connect to motor A- wire

B+

Connect to motor B+ wire

B-

Connect to motor B- wire

3.5 P5 - Tuning Port

EM870S has a tuning port with RS232 to modify the drive parameters, it’s only for tuning, not for equipment control
because neither precision nor stability is sufficient. If you need a field bus drive, use a Leadshine RS485 or EtherCAT
type drives:
(

http://www.leadshine.com/ProductSubType.aspx?type=products&category=stepper-products&producttype=stepper-dr

ives&subtype=network-stepper-drives

The interface definition is as follows:

3.6 Status LED Lights

There are two LED lights for EM870S. The GREEN one is the power indicator which should be always on in normal
circumstance. The RED one is a drive status indication light, which will be OFF while working normally but ON and
flash 1 or 2 times in a 3-second period in the case of enabled over-current or over-voltage protection.

«
...
5
6
7
8
9
...
»

Содержание EM870S


















Отзывы:

Нет отзывов