Leader F1620 Скачать руководство пользователя страница 36

Страница: 36 / 46

Portable Plasma Torch Height Controller Manual (F1620)

Figure 3.10 Three proximity switch connection method

Warning

：

）

It is better for user to connect NPN proximity switch as above drawing. By this
method, any one of them effective, THC can receive this signal.

）

When user use a NPN normally open proximity switch(or some NPN normally
open proximity switch ), L09 should be set as 0.

）

When proximity switch is breaking away from, the red indictor light of proximity
switch can be . At the same time, the collision indictor in THC panel can be
lighted.

）

In genal, if collision and torch incline do not happen, the red indictor light of
proximity switch will be lighted straight.

3.2.4 USB port

THC have a function which can make firmware procedure upgrade. User can use

USB flash disk, make it connect this USB port, then it can make firmware procedure
upgrade.

The upgrade method

：

）

Copying the firmware program named “pthc.bin” or “f1620.bin” to the root
directory of USB flash disk.

）

Power off THC, and then insert this USB flash disk.

）

Power on THC. After THC power on, the green nixie tube may display

Содержание F1620















































Результаты поиска

Содержание F1620

Отзывы:

Похожие инструкции для F1620

Бренды по названию

Популярные бренды

Leader F1620, Руководство пользователя

Результаты поиска

Содержание F1620

Отзывы:

Похожие инструкции для F1620

Бренды по названию

Популярные бренды