LDG AT-897Plus Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 22

background image

PAGE 7

Front Panel

On the front panel there is one pushbutton and one LED indicator light.

•

Tune Button:

Initiates either a memory tune or a full tune, and also toggles the tuner

between “active” and “bypass” modes.

•

Status LED:

Lights to give feedback on button presses, lights during tuning; gives tune

status at the end of a tuning cycle.

«
...
5
6
7
8
9
...
»

Содержание AT-897Plus























Отзывы:

Нет отзывов

Похожие инструкции для AT-897Plus

Бренд: Amino Страницы: 2

Бренд: ZeeVee Страницы: 32

ATI-TV WONDER VE

Бренд: ATI Technologies Страницы: 48

Бренд: Encore Страницы: 18

Бренд: Teac Страницы: 27

Sound Player - 2

Бренд: Elko Страницы: 19

Бренд: Teac Страницы: 88

Бренд: Pyle Страницы: 1

Бренд: Smarty JR Страницы: 16

Бренд: Qwik Tune Страницы: 2

Бренд: tbs electronics Страницы: 21

Бренд: Icom Страницы: 20

Бренд: Rotel Страницы: 4

Бренд: Rotel Страницы: 4

Бренд: Rotel Страницы: 4

Бренд: Rotel Страницы: 5

Бренд: Rotel Страницы: 5

Бренд: Rotel Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды