LCPRO SHARKi Скачать руководство пользователя страница 23

21

Problem

Possible Cause

Suggested Correction

solve the problem and replace components as

required

Thermostat damaged.

Replace.

Shaking, wrong

position, and out

of control gobo

wheel

No function the connector between gobo

wheel motor and drive, loose, damaged, or

broken cables connecting the gobo wheel

and drive.

Reconnect the gobo wheel motor to the drive,

and replace cables as required.

The gobo wheel motor's drive IC on the PCB

might be out of condition.

Replace the drive having the same software

version as required.

Dislocated magnetic tube and positioning

magnet, or damaged magnetic tube.

Calibrate the position of the magnetic tube

to

the positioning magnet, and replace

magnetic

tube as required

Shaking motor, wrong rotation angle, losing

step or damaged motor

Replace the motor as required.

Decreased

brightness, uneven

pattern projections

Normal end of lamp life.

Test the lamp in an adjacent fixture which is

known to be operating properly and then replace

as necessary

The midline of the lamp is not aligned with

the center point of the effect assembly

(consisting of the rotating gobo wheel, static

gobo wheel, color wheel, strobe, prism, and

frost), focus module, and object lens.

Reinstall the lamp. Adjust the lamp position

until the midline of the lamp is aligned with the

center point of the effect assemblies (consisting

of the rotating gobo wheel, static gobo wheel,

color wheel, strobe, prism, frost, the focus

adjusting module, and the object lens).

Excessive dusts or smudges on the effect

assembly, focus module and objective lens.

Follow the instructions stated in this user

manual to clean the effect assembly, focus

module and objective lens.

Damaged or deformed effect assembly,

focus module or objective lens.

Replace the damaged or deformed components

Wrong color

Normal end of lamp life

Test the lamp in an adjacent fixture which is

known to be operating properly and then replace

as necessary

Excessive dusts or smudges on the rotating

gobo wheel or color wheel.

Follow the instructions stated in this user

manual to clean the rotating gobo wheel or color

wheel.

Rotating gobo wheel, color wheel with

coating wearing off, damages or deformation

Replace the worn-off, damaged or deformed

rotating gobo wheel and color wheel

Содержание SHARKi

























Отзывы: