background image

Lamorinièrestraat 33-37

2018 Antwerp - Belgium

www.lazersport.com

For other and more helmet 

instructions, please refer to  

the owner manual included  

with the helmet.

Thank you for choosing the Lazer helmet. 

You have made an excellent choice that 

will help to reinforce your safety while 

cycling: the sport for which this helmet 

has been designed. Lazer helmets 

conform to the strict criteria  

of international standards.

Wearing a helmet may reduce the 

seriousness of injuries to the head that 

may occur during a sports accident.  

For this reason, it is important to  

use this protective gear properly.

Instructions for use and care 

1)  No helmet can protect the wearer  

  against all possible impacts.

2)  The helmet is designed to be retained  

  by a strap under the lower jaw.

3)  To be effective, a helmet must fit and be  

  worn correctly. To check for correct  

  fit, place helmet on head and make any  

  adjustments indicated. Securely fasten  

  retention system. Grasp the helmet and  

  try to rotate it to the front and rear.  

  A correctly fitted helmet should be  

  comfortable and should not move forward 

  to obscure vision or rearward to expose  

  the forehead.

4)  No attachments should be made to the  

  helmet except those recommended by  

  the helmet manufacturer.

5)  The helmet is designed to absorb shock  

  by partial destruction of the shell and liner.  

  This damage may not be visible. Therefore,  

  if subjected to a severe blow, the helmet  

  should be destroyed and replaced even  

  if it appears undamaged.

6)  The helmet may be damaged and  

  rendered ineffective by petroleum and  

  petroleum products, cleaning agents,  

  paints, adhesives and the like, without  

  the damage being visible to the user.

7)  A helmet has a limited lifespan in use and  

  should be replaced when it shows obvious  

  signs of wear.

8)  This helmet should not be used by children  

  while climbing or doing other activities  

  where there is a risk of hanging or  

  strangulation if the child gets trapped  

  whilst wearing the helmet.

9)  This helmet is designed only for the  

  following activity: cycling, roller skate,  

  skateboard. It is not designed to be used  

  with mopeds or any other type of sport,  

  mechanical or not.

Содержание BULLET 2.0









Отзывы: