LawnMaster LB4030001S Скачать руководство пользователя страница 9

7

 

7. 

Replace  the  sprocket  cover

  (10)

  and  turn  the 

chain  tensioner  knob  (12)  until 

nearly  tight,  turn  the 

chain  tnesioner  adjustment  ring  (11)  u

ntil

 

the 

saw  chain 

is  properly tensioned.  The  guide  bar  must then 

be 

pushed  upwards,  check  chain  tension  again,  do  not 
tension the chain too tight.

8. After the chain is well-tensioned

  using  the 

chain 

tensioner  adjustment  ring

, tighten

  the 

chain  tensioner 

knob 

and  clip  this  into  place.

ADJUSTING THE CHAIN TENSION

 

See page 

13

. See page

 22

.

1.

Loosen the chain tensioner 

(12) 

knob slightly by 

turning it

 

counterclockwise.

2.

To increase the chain tension, turn the chain tensioner

 

adjustment ring 

(11) 

clockwise and check the chain 

tension

 

frequently. To reduce the chain tension, turn 

the chain

 

tensioner adjustment ring counterclockwise 

and check

 

the chain tension frequently.

3.

The chain tension is correct when the gap between the 
cutter in the chain and the bar is between 3 mm - 4

mm.

 Pull the chain in the middle of the lower side of the 

bar downwards (away from the bar) and measure the

 

distance between the bar and the chain cutters.

4.

Tighten the chain tensioner knob by turning it clockwise.

 

OPERATION

ADDING CHAIN LUBRICATING OIL

 

See page 

12

.

 WARNING

Never work without chain lubricant. If the saw chain is 
running without lubricant, guide bar and saw chain can 
be damaged. It is therefore essential to check the oil 
level in the oil level gauge frequently and every time 
before starting to use the chain saw.

1.

Clear surface around the oil cap to prevent
contamination.

2.

Unscrew and remove the cap from the oil tank.

3.

Pour the oil into the oil tank and monitor the oil level
gauge. Ensure that no dirt enters the oil tank while
filling.

4.

Put the oil cap back on and tighten it up. Wipe away

 

any spillage.

5. A

 full oil tank will enable you to use the saw for 20-40

min

utes.

Recommended chain lubricating oil

The manufacturer recommends you use only

      Prime 

Parts 

chainsaw lubricating oil. 

INSTALLING BATTERY PACK

 

See page 

12

.

1. Place the battery pack in the chain saw. Align raised

ribs on battery pack with grooves in the chain saw’s
battery port.

2. Make sure the latch on bottom of the battery pack

snaps in place and that battery pack is fully seated and 
secure in the chain saw before beginning operation.

HOLDING THE CHAIN SAW

See page 

13

.

Always hold the chain saw with your right hand at the rear 
handle and your left hand at the front handle. Grip both 
handles with the thumbs and fi ngers encircling the handles. 
Ensure that your left hand is holding the front handle so 
that your thumb is underneath.

STARTING THE CHAIN SAW

See page 

13

.

1. Before starting for operation, you should install the

battery pack in the machine, and make sure chain
brake is in run position by pulling chain brake lever /
hand guard toward the front handle.

2. To start the machine: pull the trigger release, and then

press the throttle trigger.

CHECKING AND OPERATING CHAIN BRAKE

1. Engage the chain brake by rotating your left hand

around the front handle. Allow the back of your hand to 
push the chain brake lever/hand guard toward the bar
while the chain is rotating rapidly. Be sure to maintain
both hands on the saw handles at all times.

2. Reset the chain brake back into the Run position by

grasping the top of the chain brake lever / hand guard
and pulling toward the front handle until you hear a
click.

 WARNING

If the chain brake does not stop the chain immediately, or 
if the chain brake will not stay in the run position without 
assistance, take the saw to an authorised service centre 
for repair prior to use.

TRANSPORTATION AND STORAGE

 

See page 

24

.

 

Stop the machine, remove the battery pack and allow
the tool to cool before storing or transporting.

 

Clean all foreign material from the product. Store it in
a cool dry and well-ventilated place that is inaccessible 
to children. Keep away from corrosive agents such
as garden chemicals and de-icing salts. Do not store
outdoors.

 

Fit guide bar cover before storing the unit, or during
transportation.

 

For transportation, secure the machine against
movement or falling to prevent injury to persons or
damage to the machine.

MAINTENANCE

 WARNING

Use only original manufacturer’s replacement parts, 
accessories and attachments. Failure to do so can 
cause possible injury, poor performance and may void 
your warranty.

Содержание LB4030001S





























Отзывы: