background image

Setup

Important:

Remove and discard the protective

plastic sheet that covers the engine.

1

Attaching the Handle

No Parts Required

Procedure

WARNING

Folding or unfolding the handle improperly can
damage the cables, causing an unsafe operating
condition.

Do not damage the cables when folding or
unfolding the handle.

If a cable is damaged, contact an Authorized
Service Dealer.

1. Remove the handle knobs from the machine housing

(Figure 3).

Important:

Route the cables to the outside of

the handle as you install the handle.

1

g017343

Figure 3

1.

Handle knob (2)

2. Align the holes in the ends of the handle with those

in the machine housing and loosely screw the handle
knobs back in.

3. Move the handle to the operating position and

tighten the handle knobs as tightly as you can.

Figure 4

2

Filling the Engine with Oil

No Parts Required

Procedure

Your mower does not come with oil in the engine.

1. Remove the dipstick (Figure 5).

Figure 5

2.

Slowly

pour oil into the oil fill tube until the oil

level reaches the Full line on the dipstick (Figure 5).

Do not overfill.

(Max. fill: 22 oz. (0.65 l), type:

10W-30 or SAE 30 detergent oil with an API service
classification of SJ or higher.)

Note:

Each time you check the oil level, remove the

dipstick and wipe it clean, insert it into the oil filler
neck (but

do not

screw it in), then remove it again

and check the level (Figure 5).

Note:

If you overfill the engine, pour some oil out

of it as directed in Changing the Engine Oil.

3. Install the dipstick securely.

5

Содержание 10607

















Отзывы: