manualshive.com logo in svg

Lawler 803 SEA Basic, Инструкция по установке и обслуживанию, Страница: 3 / 4

Поделиться
Скачать
Lawler 803 SEA Basic Скачать руководство пользователя страница 3

 

-3-

      

Model 803 Repair Parts

Figure C

  Item  Description 

Part  No.

 1  Actuator 

—

  7 

Bonnet Gasket 

 8  Dome 

—

  10  Liner O-Ring 

 11  Liner

 12  Plunger

  12a  Piston Liner Assembly  Figure C

  13  Valve Spring 

—

  14  Bottom Plug 

—

  18  Pusher O-Ring 

 19  Bonnet 

 21  Pusher 

 22  Thermostat 

  23  Body Screw  (NS) 

  24  Liner Gasket, Upper 

  25  Valve Body 

—

 26  Tailpiece 

—

  27  Union Nut 

  28  Stop & Check Stem 

  29  S & C Stem O-Ring 

  30  S & C Bonnet 

—

 31  Strainer 

—

  32  S & C Spring 

—

  33  Shutoff Disc Assembly 

—

  34  S & C Body 

—

  35  Seat O-Ring 

—

 36  Pushrod 

—

  37  Spring Retainer 

—

  38  Relief Spring 

—

  39  Acorn Nut

  40  Nameplate  (NS) 

—

  41  Liner Gasket, Lower 

—

  42  S & C Gasket 

—

   

(NS) - Not Shown

   

12a Only available in Assembly

805 cut-away

11

12

36

37

39

38

See Fig. B

8

7

See Fig. C

42

10

13 14

41

35

34 33

32

31

30

29

28

27

26

25

24

22

1

19

18

21

Figure B

Repair Kits and Assemblies

 

Item  Description 

Contains 

Part No.

 

1  Complete Repair Kit 

7-10-12a-13-18-22-24-31-32-35  79978-10

 

2  Piston and Liner Assy.  11-12a 

71946-16

 3 

Stop and Check Repair Kit 28-29-31-32-33-35 

79909-02

 

4  Thermostat  Repair Kit  7-22 

72911-11

 

5  Bonnet Assy. 

1-2-18-19-21 

71965-11

 

6  O-Ring and Gasket Kit  7-10-18-24-29-35-41-42 

79830-03

Kit H

Содержание 803 SEA Basic

Страница 1: ... electrical shock General Description The Model 805 water temperature controller is care fully assembled and tested at the factory to mix hot and cold water to any desired temperature within range The temperature of the hot water should be at least 20 F higher than the maximum valve setting The major safety features are 1 Failure of cold water supply causes the hot water ports to reduce hot water ...

Страница 2: ...r With the liner out of the valve replace liner O ring 10 Note If the piston or liner is nicked or shows signs of excessive wear it should be replaced Caution The liner and plunger cannot be dropped please handle carefully The liner must be in serted correctly Carefully examining the outside of the liner will reveal a very small difference in diameter between the upper half and the lower half On r...

Страница 3: ...at O Ring 36 Pushrod 37 Spring Retainer 38 Relief Spring 39 Acorn Nut 40 Nameplate NS 41 Liner Gasket Lower 42 S C Gasket NS Not Shown 12a Only available in Assembly 805 cut away 11 12 36 37 39 38 See Fig B 8 7 See Fig C 42 10 13 14 41 35 34 33 32 31 30 29 28 27 26 25 24 22 1 19 18 21 Figure B Repair Kits and Assemblies Item Description Contains Part No 1 Complete Repair Kit 7 10 12a 13 18 22 24 3...

Страница 4: ...ng this procedure 6 Allow water to flow through the mixing valve until the water temperature is stable If necessary readjust the mixing valve in accordance with the TEMPERATURE ADJUSTMENT section of the installation manual 7 Once the temperature is set start the recirculating pump and allow the system to reach set tempera ture 8 Measure the water temperature at the return pump and adjust the aquas...

Отзывы:

Нет отзывов