background image

8

Open the water supply.

The  cleaner  can  be  connected  directly  to  the  mains 

drinking water supply only if the supply hose is fitted 

with a backflow preventer valve as per current regula-

tions in force. 

Make sure that the hose is at least Ø 13mm and that it 

is reinforced.

Water supply from an open container

Unscrew the coupling part for the water inlet.

Screw  the  suction  hose  with  filter  (not  included) 

onto the water connection of the unit.

Hang the filter in the container.

Vent the unit before operation.

-  Unscrew  the  high-pressure  line  at  the  high-

pressure outlet of the unit.

-  Switch on the unit and let it run until water free 

of bubbles emerges at the high-pressure out-

let.

-  Switch off the unit and screw on the high-pres-

sure hose again.

Failure to comply with the above conditions causes se-

rious mechanical damage to the pump and the loss of 

warranty cover.

1.

Connect  the  high  pressure  hose  to  the  unit’s  high 

pressure outlet

 (fig.5).

fig. 5

2. C

onnect  the  high  pressure  hose  to  the  spray  gun

Insert  the  spray  wand  of  your  choice  into  the  wand 

extension.  Press  in  against  the  spring  tension  and 

twist into the locked position (fig. 6). Insert the nozzle 

(fig.2A).

fig. 6

3. 

Connect garden hose to unit’s water inlet 

(Max 10 bar,  max t. 40° C) (fig. 7).

fig. 7

4.

Connect garden hose to the cold 

water source and turn water on completely (fig. 8).

fig. 8

13 mm

5. 

Trigger  the  gun  to  eliminate  trapped  air,  wait  for  a 

steady flow of water to emerge from the spray nozzle

 

(fig. 9).

fig. 9

CAUTION!

 

In  order  to  assist  the  first  startup,  it  is 

recommended to hold the trigger pressed during the 

pulling of the starter handle

6. Push the fuel cock to ON position (Fig. 10).

ON

ON

           Fuel cock

fig. 10

7. Push the choke lever to the OFF position OFF (Fig. 11).

fig. 11

Chock lever

  CLOSE

OFF

NOTE:  

Do not the choke if the engine is warm or 

the air temperature is high.

8. Start the engine (Fig. 13).

fig. 13

Engine 

switch

Starting rope handle

ON

a) Push the engine switch to the ON position.

b) Pull slightly the starting rope handle up until feeing 

Содержание CONTRACTOR 2800














Отзывы: