Rev. A 5/20
2
2084917
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
CAUTION
•
AVOID
the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these de-
vices may overheat and cause a fire hazard.
•
DO NOT
route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a
fire hazard.
•
ALWAYS
place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
•
NEVER
insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
•
DO NOT
block, cover or obstruct air flow to or from the Fan while in operation.
•
DO NOT
use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may
create a shock hazard.
•
DO NOT
run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will not be tripped over.
•
NEVER
use a single extension cord to operate more than one Fan or other electrical device.
•
DO NOT
use this Fan if it has been damaged or is not functioning properly.
• Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,
move the Fan to another location.
• Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
•
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008)
. This Fan is not suitable for use in agricultural
facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article
547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
•
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008)
. This Fan is not suitable for use in hazardous lo-
cations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
NOTICE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user is cautioned that changes
and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT
use this Fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!
ALWAYS
be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet and
create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition should
be replaced by a qualified electrician.
ALWAYS
unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means
of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the
Fan when not in use.
BE CERTAIN
that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The
Blue Plug
™
on your Lasko Fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed
or tampered with. To reduce the risk of fire, electric shock and personal injury,
DO NOT
attempt to remove, replace, repair or tamper
with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.
THIS FAN HAS A POLARIZED PLUG
(one blade is wider than the other). This plug is designed to fit into the outlet only one way.
Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety feature. If the
plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced.
Rev. A 5/20
7
2084917
1 Rejilla
Frontal
3 Tapa de Ventilador
4 Tuerca
5 Helice
6 Conjunto de Cabezal
7 Tubo
8 Base
9 Control
Remoto
2 Parrilla Trasera
1. Ensamble la cabeza
del ventilador
3. Afloje la tuerca, extienda la tubería
hacia arriba, apriete la tuerca
2. Gire el tubo hacia abajo
en la base
Botón de Encendido
ENCENDIDO/APAGADO el Ventilador
presionando el Botón de Encendido
Botón de Velocidad
La velocidad del ventilador se
puede ajustar a 1, 2, 3, o 4
1
2
5
6
8
9
7
Empuje la perilla ubicada en la parte
superior de la caja del motor para hacer
que la cabeza del Ventilador se mueva
de un lugar hacia otro.
Para ajustar la direccion del
aire, simplemente jire la cabeza
del ventilador.
3
4
4. Conjunto de cabeza gir-
atoria abajo en la tubería
Up: Stationary
Down: Oscillate
Partes Incluidas
Ensamblaje
(Video Tutorial de Ensamblaje: www.lasko.com/how-to)
Oscilación
Inclinación
Controles
