MODEL 2505
OPERATION
This Fan may be operated by the Manual
Controls located on top of the unit (as shown in
Figure 5
)
or by the Remote Control (shown in
Figure 6)
.
1. Place the Fan on a firm and level surface.
CAUTION:
Plastic or rubber tabs, like the feet on this unit,
may stick to furniture surfaces and/or hardwood floors. The
unit may leave a residue that could darken, stain or leave
permanent blemishes on the finish of certain furniture sur-
faces, including wood surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they
may slip partially or completely out of the
receptacle with only the slight movement of
the attached cord. Receptacles in this con-
dition may overheat and pose a serious fire
hazard; if covered by a curtain or drape, the
fire hazard is even greater.
3. Turn the Fan ON by pressing the
Power Button
( ).
4. Upon turning the Fan ON, the unit will be on HIGH.
5. Pressing the
Power Button
a second time will set the
Fan to MEDIUM.
6. Pressing the
Power Button
a third time will set the Fan
to LOW.
WARNING
Rev. G 11/15
4
2505ES
Rev. G 11/15
9
2505ES
7.
OSCILLATION:
Press the
Oscillation Button
( ) to start
and stop the oscillation function.
8.
TIMER:
The timer function allows the unit to be set to
operate for a length of time from 1 hour to 7 hours, in
increments of 1 hour. Press the
Timer Button
( ) to set
the length of time desired. Each time the timer button is
pressed, the time is increased by 1 hour. After reaching
7 hours, pressing the timer button once more will reset
the Fan to continuous running. The lights on the front of
the unit will light up appropriately with the length of time
that the Fan is set for.
9.
IONIZER:
The ionizer function on this Fan will operate
within any speed mode. Press the Ion Button ( ) once
to turn this function on and a second time to turn it off.
The Fan must be ON for the ionizer to be functional. When
the ionizer is turned on it will assist in the purification of
the room air.
10.To turn the Fan OFF, press the
Power Button
( ) until unit
turns off then unplug the unit from the electrical outlet.
Figure 5
Oscillation
Button
Power
Button
Timer Button
Ionizer Button
MODELO 2505
ENSAMBLADO
1. Cuidadosamente retire el ventilador de la bolsa plástica y de
la caja. Para facilidad de ensamblado, coloque el ventilador
en forma horizontal para que la parrilla frontal esté apuntando
hacia abajo.
2. Arme las
Bases de Apoyo
interconectando las
Salientes
en la
Base de Apoyo A
dentro de los
Orificios de Salientes
en la
Base
de Apoyo B
. Introduzca el
Cable Eléctrico
a través del orificio
grande en el centro de la
Montura de la Base de Apoyo
.
(Figura 1)
3. Asegure los
(4) Tornillos
en los cuatro orificios de la parte inferior
de la base.
(Figura 2)
4. Alinee las
Lengüetas de Alineación de la Montura de la Base
de Apoyo
con las ranuras de alineación en la parte inferior del
ventilador, teniendo cuidado de que el canal del cable en la
parte inferior de la base de apoyo debe estar apuntando hacia
la parte posterior del ventilador.
(Figura 3)
5. Asegure la
Montura de la Base de Apoyo
a la parte inferior
del ventilador con
(4) Tornillos de Largo
. Suavemente elimine
cualquier sobrante del
Cable Eléctrico
y colóquelo en el
Orificio
de Colocación del Cable
.
(Figura 4)
Tornillos
Montura de la
Base de Apoyo
Cable Eléctrico
Orificio de
Colocación del
Cable
Figura 4
Montura de la Unidad de base a Parte Inferior
Ranura de
Alineación
Lengüeta de
Alineación de la
Montura de la Base
de Apoyo
Figura 3
Canal del Cable
Figura 2
Montura de la Base de Apoyo - Vista Inferior
Montura
de la Base
de Apoyo
Tornillos
Figura 1
Base de
Apoyo B
Base de
Apoyo A
Salientes
Montura de la Base de Apoyo