LASER COMPONENTS COUNT Series Скачать руководство пользователя страница 1

Страница: 1 / 11

10/21 / V21 / OS-IF / manuals/lc-photon-counter/count-series-user-manual

Single Photon Counting Module

COUNT

-Series User Manual

Table of Contents

Introduction 2
Mounting the Count

Handling single photon counting modules

Heat dissipation

Gating function and TTL output

Optical fiber connection

Electrical connections (rear side)

Powering up the module

Optimizing performance

Technical specifications for COUNT

module

Technical sSpecifications for COUNT

BLUE module

Technical specifications for COUNT

NIR module

Absolute maximum ratings

Interface information

Individual module test data

ESD information

Safety

RoHS compliance

Warranty

Product number designations

Support 11

Detectors

Germany and Other Countries

Laser Components Germany GmbH
Tel: +49 8142 2864 – 0
Fax: +49 8142 2864 – 11
[email protected]

www.lasercomponents.com

Содержание COUNT Series












Результаты поиска

Содержание COUNT Series

Отзывы:

Похожие инструкции для COUNT Series

Бренды по названию

Популярные бренды

LASER COMPONENTS COUNT Series, Руководство пользователя

Результаты поиска

Содержание COUNT Series

Отзывы:

Похожие инструкции для COUNT Series

Бренды по названию

Популярные бренды