MODEL 4890
Rev. A 6/07
4
2085461
Rev. A 6/07
9
2085461
MODEL0 4890
OPERATION
(Figure 5)
1. Plug the cord set into a 120 volt outlet. When the Fan is plugged in, it will “beep” to indicate there is power to the Fan.
DO NOT USE
EXTENSION CORDS WITH THIS FAN.
Extension cords may overheat and cause a fire.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of
the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain,drape, etc. the
fire hazard is even greater.
2. Test GFCI (Ground Fault Circuit Interrupter) plug
BEFORE EACH USE:
1. Plug GFCI into outlet. Indicator light on the GFCI plug should turn on.
2. Press test button. Indicator light on the GFCI plug should turn off.
3. Press reset button for use. Indicator light on the GFCI plug should turn on.
4. DO NOT USE IF ABOVE TEST FAILS.
Power and Speed Control:
1. Turn the Fan
ON
by pressing the
Power/Speed Button
( ) located on the front of the unit. The Fan will start in
High Speed
.
2. Press the
Power/Speed Button
( ) a 2nd time for
Medium Speed
.
3. Press the
Power/Speed Button
( ) a 3rd time for
Low Speed
.
4. Press the
Power/Speed Button
( ) a 4th time to turn the Fan
OFF
.
Internal Oscillation Control:
NOTE:
This Fan is equipped with an Internal Oscillation Function. The movement occurs INSIDE the Fan housing
- the whole Fan WILL NOT move side to side.
1. To turn
ON
the internal oscillation function, press the
Oscillation Button
( ) once. The Oscillation Button will ‘blink’ to indicate that the
Fan is oscillating.
2. To turn
OFF
the internal oscillation function, press the
Oscillation Button
( ) a second time.
Control Panel Light:
When the Fan is initially plugged in, the
Control Panel
will be lit.
1. To turn the
Control Panel Light
OFF
,
press and HOLD
the
Power/Speed Button
( ) for 3 seconds.
2. To turn the
Control Panel
Light
ON
again,
press and HOLD
the
Power/Speed Button
( ) for 3 seconds.
Accent Lighting:
This Fan includes a maintenance-free, soft LED accent lighting function for nighttime use. This function can be used while the Fan is ON or
OFF.
1. Press and release the
Light Button
( ) to turn the
Fan Accent Lighting
ON
to full brightness.
2. Pressing and holding the
Light Button
( ) will allow the light level to dim up and down to the desired brightness.
3. Press the
Light Button
( ) to turn the
Fan Accent Lighting
OFF
.
Figure 5
ARMADO
(Figuras 1 a 4)
NO SE REQUIEREN HERRAMIENTAS
1. Retire el ventilador y sus partes de la caja de cartón.
2. Coloque el ventilador en el lugar deseado al aire libre o en interiores sobre una superficie firme, plana y nivelada.
3. Introduzca manualmente la
Varilla de Metal
en el orificio ubicado en la parte superior del ventilador. La varilla de metal habrá quedado
firmemente asegurada en su lugar cuando usted ya no pueda seguir atornillándola.
(Figura 1)
4. Coloque la
Cubierta del Ventilador
sobre el ventilador con la flecha ubicada en el lado inferior de la
Cubierta del Ventilador
apuntando
hacia el frente del ventilador donde están ubicados los botones de control.
(Figuras 2 y 3)
5. Coloque la
Tapa del Ventilador
sobre la
Varilla de Metal
en el centro de la
Cubierta del Ventilador
.
(Figura 4)
6. Enrosque la
Tapa del Ventilador
en forma manual a la
Varilla de Metal
hasta asegurar completamente.
NO AJUSTE EN EXCESO.
Figura 4
Cubierta del
Ventilador
Tapa del
Ventilador
Varilla de Metal
Figura 3
Varilla de
Metal
Cubierta del
Ventilador
Flecha en el Lado Inferior de la
Cubierta del Ventilador
Apunte la Flecha Hacia
el Frente del Ventilador
Figura 2
Figura 1
Varilla de Metal
Parte Superior del
Ventilador
Light
Power/Speed
Oscillation
Control Panel
Control Panel
Lens