The Stryker Light is a 2-Speed Searchlight with Directional Flexibility
which gives the operator a full 370° horizontal rotation and a 135°
vertical tilt with fingertip control. The Stryker Light provides superior
light penetration with the new Cr5 PentaBeam II technology.
Stryker Light Hard Wired - Permanent Mount:
Stryker Light Searchlight
Dash Control
Wiring Harness
Rockguard
Permanent Mounting Gasket
Permanent Mounting Plate
Mounting Screws
Stryker Light Wireless - Permanent Mount:
Stryker Light Searchlight
Remote Control (Per Model Number)
2 - 23A 12V Batteries
Permanent Mounting Gasket
Permanent Mounting Plate
Mounting Screws
Rockguard
Stryker Light Wireless - Magnetic Mount:
Stryker Light Searchlight
Wireless Hand Held Remote Control
2 - 23A 12V Batteries
Rockguard
MOUNTING INSTRUCTIONS
Light Unit/Permanent Mount
Determine the location for the light on your vehicle or boat. Remove
the mounting plate from the light. Center the mounting plate with the
vise screw on the mounting plate to the back. Mark the hole locations
for the three mounting screws and drill a pilot hole for each with 1/8
inch bit. Fasten the stainless steel mounting plate with the 3 #10 –
16x3/4 type AB cross recessed pan head
tapping screws. Drill a 1/4” hole (wireless) or a 5/8” hole (hard-wired)
in the center of the mounting plate opening to accommodate the power
wire or wiring harness and connector. Attach the
connector that is affixed to the underside of the light to the
corresponding connector on the wiring harness (hard-wired).
Position the connection point beneath the mounting surface, and apply
silicone sealant around wire to seal the drilled opening.
Wet the mounting surface with a small amount of water or
lubricant for easier installation, then place the light over the
mounting plate by sliding the front of the light over the front of the
mounting plate, first pull the light backwards, then seat the back of the
light on to the mounting plate. Displace the back of the gasket and
install the vise screw (provided). Tighten the vise screw using a Phillips
head screwdriver. Replace the gasket.
Power Supply
Connect the deutsch connectors for all cables. There is one that
connects to the golight and one that connects to the transformer.
Be sure these are securely fastened. Then plug the transformer
into a compatible outlet providing 110V AC. The light is now
powered and will operate with the remote control.
Dash Control/Permanent Mount
Determine the appropriate location for the dash mount control and
create a 2 inch opening to accommodate the cylinder on the rear of
the remote. Remove the outer rubber cover and affix the control to
the dash with the four screws provided. The word ”TOP” is em-
bossed on the control and should be situated accordingly. All wiring
should be undertaken with power removed from the system. First, at-
tach the connector that is affixed to the control to the corresponding
connector on the wiring harness. Next, join the leads at the remote
to 12volt DC power with appropriate automotive wire attachments;
the red wire is the positive lead and the black wire is the negative
lead--the unit is polarity sensitive and care must be taken to observe
this. Note: Once power is applied to the system the light will pan
and tilt prior to bulb illumination. As a safety feature, the control is
backlit to indicate bulb illumination only.
Each spotlight needs to be wired on a single dedicated circuit and
the power fused at 10 amps. With the power connected, your light is
ready for operation.
Wireless Dash Control
If you have a wireless dash control, please note that it is vital for this
to be attached to a flat / smooth surface with the 4 mounting screws
included. The arrow under the rubber cover should point up.
BATTERY INSTALLATION AND REMOVAL FOR TRANSMITTER
Remove battery cover: for wireless hand-held transmitter, remove
phillips head screw to remove cover. For wireless dash mount remote,
simply remove the exterior rubber cover. With battery compartment
now exposed, insert batteries according to the correct polarity or
gently remove batteries by grabbing the positive end and lifting up.
PROGRAMMABLE REMOTE INSTRUCTIONS
The Stryker Light is controlled with a programmable remote
with 2187 different channels. This feature allows you
the freedom to change the channel selection, and the receiver re-
learns the new selection. This light has been pre-programmed at the
factory, and it is not necessary to re-program the transmitter, unless
you experience outside interference. To program transmitter:
1.
IMPORTANT
D
:
isconnect power.
2.
Remove battery cover from remote control.
3.
Set the 7 dip switches to a selection of your choice. There are 3
positions on each; positive, negative and neutral. Use a small
screwdriver and select a position for each dip switch. *Please
note that the orientation of the +/- switch positions may vary
among different models of wireless remote controls.
4.
Insert both GP 23A 12V batteries. Be sure batteries have
adequate charge.
5.
Replace battery cover.
a.
Depress the on/off button and hold it down. Red LED will
light.
b.
While holding the on/off button down, reinstall the power
(replace fuse or connect vehicle battery).
c.
Keep on/off button depressed for 5-6 seconds, and
then release. The light should now be programmed.
OPERATION OF STRYKER LIGHT
1.
Using the remote control, turn on the light by depressing the on/
off button.
2.
With the joystick on the dash control, rotate your light to the
desired location.
3.
The speed of the light rotation can be controlled by depress-
ing the fast/slow button one time and by depressing it again to
restore the original speed.
4.
The spotlight should not be turned on when the snap on lens
cover (rockguard) is attached. The hard wired dash control will be
backlit when the bulb is illuminated.
USAGE:
» This light is intended for off-road and utility use only
» This light is intended to be mounted outside the vehicle while in
use
» This light may only be disassembled and repaired by an
authorized representative
MISUSE:
» This light is not approved for road or highway use
» This light is not approved for underwater use
» This light is not approved for inverted mounting
» This light is not approved for use inside a vehicle or enclosure and
power should be disconnected prior to placing the light in such
circumstance
» This light may be damaged if operated in icing conditions
» This light may only be dismantled by an authorized Golight repre-
sentative
»
Any violation of the above referenced misuses will be
considered grounds for warranty refusal
