Larson Electronics LEDEMG-400VA Скачать руководство пользователя

Страница: 3 / 13

Section 100 System Installation Instructions

101. Specifications Input

• Input voltage: 120 VAC.

• Input frequency: 60HZ ±2%

• Operating temperature: 20ºC to 30ºC (68ºF to 86ºF)

• Synchronizing slew rate: 1 Hz per second nominal

• Input surge protection: Meets UL 924

Output

• Output voltage: 120 VAC, 60HZ.

• Output regulation: (static) ±5% based on a 0% - 100% resistive load

• Minimum loading: none required

• Output distortion: Less than 3% THD linear load

• Load power factor: .5 lag to .5 lead

• Output frequency: Normally, Synchronized to utility, ±2 Hz during emergency

• Overload: 150% for five seconds

• Time to transfer to inverter after a utility power failure: <1 ms.

Battery

• Battery type: Maintenance free sealed lead calcium

• Battery charger: Fully automatic with temperature compensation

• Recharge time: Meets UL requirements (72 Hours)

• Battery protection: Automatic low-battery voltage disconnect and reverse polarity protection.

Automatic restart upon utility return

• Battery switch: Also used as battery isolator

• Standard battery: Sealed lead-calcium: 10-year life

• Battery voltage: 72

• Runtimes: 90 minutes.

• Operating temperature: 20°C to 30°C (68°F to 86°F)

Note: Battery performance rated at 25°C (77°F)

Model Number INPUT/OUTPUT

VOLTS

INPUT CURRENT

(MAXIMUM)

OUTPUT CAPACITY

RATING (90 Min.)

BATTERY

VOLTAGE

DIMENSIONS

(in)

(W x D x H)

WEIGHT

(Lbs./Kg)

LEDEMG-400VA

120

5.8A

400 Watts/440 VA

72 VDC

22 x 8 x 16

132/60.0

TABLE 1

Содержание LEDEMG-400VA














Результаты поиска

Содержание LEDEMG-400VA

Отзывы:

Похожие инструкции для LEDEMG-400VA

Бренды по названию

Популярные бренды

Larson Electronics LEDEMG-400VA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LEDEMG-400VA

Отзывы:

Похожие инструкции для LEDEMG-400VA

Бренды по названию

Популярные бренды