EPL-48-4L-LED-D-V2-100C
Larson Electronics, LLC
Phone: (800) 369-6671
Fax: (903) 498-3364
www.larsonelectronics.com
2 of 5
WARNING
TO AVOID THE RISK OF FIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTED AND MAINTAINED BY A QUALIFIED ELECTRICIAN ONLY, IN ACCORDANCE WITH ALL
APPLICABLE ELECTRICAL CODES.
TO AVOID ELECTRIC SHOCK:
•
BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•
PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•
MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•
ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•
DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•
DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•
ALL FASTENERS SHOULD BE PROPERLY SEATED.
The EPL-48-4L-LED-D-V2-100C from Larson Electronics is an Explosion Proof Dimmable LED Light Fixture that is NRTL
Listed for United States and Canada and rated Class I Divisions 1 & 2 and Class II Divisions 1 & 2 for areas where
flammable chemical/petrochemical vapors, gases and/or pulverized dust and fibers exist or have the potential to exist. This
explosion proof LED light has a T6 temperature rating and carries a paint spray booth light certification, making it ideal for
applications such as paint booths, oil rigs, offshore applications, petrochemical, manufacturing, chemical storage, water
treatment centers, and food processing plants. The EPL-48-4L-LED-D-V2-100C is equipped with 100' of 12/5 SOOW cord
that brings power to both the light and the dimming controls.
WIRING
The EPL-48-4L-LED-D-V2-100C is outfitted with 100' of 12/5 SOOW cord terminated in a blunt cut end. This cord includes
power to the light and the dimming controls.
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product
, in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 1
2
0V - 277V AC, 50 or 60Hz
.
Warning:
Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in the diagram
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
BRACKET MOUNTING
Standard end mounting via Unistrut. The Unistrut is attached to our standard L-bracket mounts. These L-bracket mounts
can be adjusted to create angle mounts. As illustrated in the photos above, the series of mounting holes at the top of the
bracket enable this explosion proof LED light to be attached to any wall, ceiling or floor surface. A simple through bolt can
be used to secure the light to the surface. A single junction box at one end of the light is provided for the electrical
connection.
SUSPENSION MOUNTING
Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2" NPT junction box
on one end, and a 1/2” NPT bracket on the other end of the fixture. Operators bring rigid pipe down to the threaded
mounting hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture’s lead wires, completing
the electrical connection. The threaded mounting bracket provides support for the opposite end of the fixture.
